Tuesday, June 28, 2011

CCNA 2 Final 2011 Answers -Cisco

CCNA 2 Final Exam Answers


CCNA 2 Final 2011 Answers – Cisco CCNA 2 Final Exam Answers
Which of the following are primary functions of a router? (Choose two.)

packet switching

microsegmentation

domain name resolution

path selection

flow control
A network administrator is in charge of two separate networks that share a single building. What device will be required to connect the two networks and add a common connection to the Internet that can be shared?

hub

router

access point

Ethernet switch
A router boots and enters setup mode. What is the reason for this?

The IOS image is corrupt.

Cisco IOS is missing from flash memory.

The configuration file is missing from NVRAM.

The POST process has detected hardware failure.


Refer to the exhibit. A network administrator adds this command to router R1: ip route 192.168.2.0 255.255.255.0 S0/0/0. What is the result of adding this command?
This route is automatically propagated throughout the network.
The traffic for network 172.16.1.0 is forwarded to network 192.168.2.0.
A static route is established.
The traffic for all Class C networks is forwarded to 172.16.1.2.

In a complex lab test environment, a router has discovered four paths to 192.168.1.0/24 via the use of the RIP routing process. Which route will be installed in the routing table after the discovery of all four paths?

R 192.168.1.0/24 [120/3] via 192.168.110.1, 00:00:17, Serial0/1/0

R 192.168.1.0/24 [120/2] via 192.168.200.1, 00:00:17, Serial0/0/0

R 192.168.1.0/24 [120/1] via 192.168.100.1, 00:00:17, Serial0/0/1

R 192.168.1.0/24 [120/4] via 192.168.101.1, 00:00:17, Serial0/1/1
Which three statements are true regarding the encapsulation and de-encapsulation of packets when traveling through a router? (Choose three.)

The router modifies the TTL field, decrementing it by one.

The router changes the source IP to the IP of the exit interface.

The router maintains the same source and destination IP.

The router changes the source physical address to the physical address of the exit interface.

The router changes the destination IP to the IP of the exit interface.

The router sends the packet out all other interfaces, besides the one it entered the router on.

Refer to the exhibit. Router R1 receives a packet for destination 192.168.1.10. Which route will be preferred for this packet?

through the Fa0/0 interface

through the Fa0/1 interface

through the S0/0/0 interface

through the S0/0/1 interface

Refer to the exhibit. Which two routes are level 1 ultimate routes? (Choose two.)

10.0.0.0

10.1.2.0

10.2.2.0

10.1.1.0

192.168.1.0

192.168.2.0
Which routing protocol by default uses bandwidth and delay to calculate the metric of a route?

RIPv1

RIPv2

OSPF

EIGRP
Which statement is true about the metrics used by routing protocols?

A metric is a value used by a particular routing protocol to compare paths to remote networks.

A common metric is used by all routing protocols.

The metric with the highest value is installed in the routing table.

The router may use only one parameter at a time to calculate the metric.

Refer to the exhibit. A router learns a route to the 192.168.6.0 network, as shown in the output of the show ip rip database command. However, upon running the show ip route command, the network administrator sees that the router has installed a different route to the 192.168.6.0 network learned via EIGRP. What could be the reason for the missing RIP route?

Compared to RIP, EIGRP has a lower administrative distance.

Compared to EIGRP, RIP has a higher metric value for the route.

Compared to RIP, the EIGRP route has fewer hops.

Compared to RIP, EIGRP has a faster update timer.


Refer to the exhibit. RIPv1 has been used as a routing protocol on the network. A new 172.16.2.0/24 network has been added on router R2 and configured under the RIP routing process. When will R1 converge?
after 13 seconds
after 30 seconds
after 180 seconds
after R1 receives triggered updates from R2

Which two statements are true for link-state routing protocols? (Choose two.)

Routers that run a link-state protocol can establish a complete topology of the network.

Routers in a multipoint network that run a link-state protocol can exchange routing tables.

Routers use only hop count for routing decisions.

The shortest path first algorithm is used.

Split horizon is used to avoid routing loops.
An administrator is configuring Router1 so that it can connect to Router2 by using IP. Which protocol can be used by Router1 to determine the IP address of Router2 when they are directly connected and only Layer 2 connectivity exists between them?

ARP

CDP

ICMP

Telnet


Refer to the exhibit. A device is required to complete the connection between router R1 and the WAN. Which two devices can be used for this? (Choose two.)
a CSU/DSU device
a modem
an Ethernet switch
a hub
a bridge


What can be determined from the output shown in the exhibit? (Choose two.)

Annapolis is a 2611 router that is connected to the S0/0 interface of the Montgomery router.

All of the routers are connected to Montgomery through an Ethernet switch.

Montgomery has Layer 2 connectivity with Cumberland.

Layer 3 connectivity is operational for all of the devices listed in the Device ID column.

An administrator consoled into the Waldorf router can ping the Brant router.

Brant, Fisherman, and Potomac are directly connected to Montgomery.

Refer to the exhibit. Which route in the routing table of R1 will be discarded by its neighboring router?

192.168.2.0

192.168.3.0

192.168.4.0

192.168.9.0

192.168.10.0

192.168.11.0


Refer to the exhibit. Based on the partial output in the exhibit, why can users establish a console connection to this router without entering a password?
The login command was not entered on the console line.
The enable password should be an enable secret password.
No username and password combination has been configured.
Console connections cannot be configured to require users to provide passwords.

Refer to the exhibit. An administrator is attempting to configure a router by copying and pasting the commands that are shown in the exhibit. However, only one of the FastEthernet interfaces is coming up. What is the problem?
Both interfaces are in the same IP subnet.
FastEthernet0/1 does not have a description.
There can be only one FastEthernet interface enabled on a router at one time.
The administrator did not exit to global configuration mode before configuring FastEthernet0/1.


Refer to the exhibit. The network administrator has run the following command on R1.

R1(config)# ip route 192.168.2.0 255.255.255.0 172.16.1.2

What is the result of running this command?


Traffic for network 192.168.2.0 is forwarded to 172.16.1.2.

This route is automatically propagated throughout the entire network.

Traffic for all networks is forwarded to 172.16.1.2.

The command invokes a dynamic routing protocol for 192.168.2.0.


Refer to the exhibit. The command ip route 0.0.0.0 0.0.0.0 S0/0/0 is run on router R2. What are the two results of this command? (Choose two.)
A static route will be updated in the routing table.
The traffic from the Internet will be directed to R2.
The traffic from the source network 172.16.0.0/22 will be blocked.
The route will be specified as the default route for all networks not defined in the routing table.
All the broadcasts will be forwarded via the S0/0/0 interface of R2.

Refer to the exhibit. All routers are running the same routing protocol. Based on the exhibit and its displayed commands, which statement is true?
The wildcard mask is incorrectly configured.
A default route must be configured on every router.
Routers B, C, and D have no access to the Internet.
The link to the ISP is not advertised by the routing protocol process.

The command ip route 192.168.2.0 255.255.255.0 172.16.2.2 was entered into the router. After network changes were made, the new next hop for the 192.168.2.0/24 network is 172.16.5.1. What should an administrator do so that the router will use the new next hop to reach the 192.168.2.0 network?

Enter the command clear ip route *.

Lower the administrative distance for the new path to ensure that it is used first.

Negate the original command and enter a new static route with the new next hop.

Nothing. The router will learn of the new next hop and automatically update the route table.


Refer to the exhibit. On the basis of the show running-config output, which option correctly reflects the routes that will be listed in the R2 routing table?


Refer to the exhibit. Routers 1 and 2 are directly connected over a serial link. Pings are failing between the two routers. What change by the administrator will correct the problem?

Set the encapsulation on both routers to PPP.

Decrease the bandwidth on Serial 0/1/0 on router 2 to 1544.

Change the cable that connects the routers to a crossover cable.

Change the IP address on Serial 0/1/0 on router 2 to 192.168.0.1/30.


Refer to the exhibit. Which combination of network ID and subnet mask can be used to meet the 24 host requirement of the LAN that is attached to Router3?
192.168.0.0/27
192.168.0.64/26
192.168.0.192/26
192.168.0.192/27


Refer to the exhibit. The networks that are connected to R1 have been summarized for R2 as 192.168.136.0/21. Which packet destination address will R2 forward to R1?

192.168.135.1

192.168.142.1

192.168.144.1

192.168.128.1

A network administrator has been asked to configure a network using a classful IP addressing scheme. Which statement is true about the IP addressing that will be used?
Classful IP addresses can be used only when static routing is configured in the network.
Classful IP addresses allow the network/host boundary to occur at any bit in the 32-bit address.
The subnet mask for classful IP addresses can be determined by the value of the first octet of the IP address.
Classful IP addresses require the subnet mask to be included in the routing updates that are propagated by the classful routing protocols.

Which range of IP addresses will be used by RIPv2, EIGRP, and OSPF routing protocols to send routing advertisements?

How will a router that is configured with a classless routing protocol determine the subnet mask that should be assigned to routes that are learned from neighboring classless routers?

The subnet mask that is included in the routing updates will be used.

The subnet mask of the interface that receives the update will be used.

The subnet mask that is specified in the network command will be used.

The class of the network in the update will determine the subnet mask that is used.


Refer to the exhibit. Both routers are using the RIPv2 routing protocol and static routes are undefined. R1 can ping 192.168.2.1 and 10.1.1.2, but is unable to ping 192.168.4.1.

What is the reason for the ping failure?
The serial interface between two routers is down.
R2 is not forwarding the routing updates.
The 192.168.4.0 network is not included in the RIP configuration of R2.
RIPv1 needs to be configured.

Refer to the exhibit. When troubleshooting a network, it is important to interpret the output of various router commands. On the basis of the exhibit, which three statements are true? (Choose three.)
The missing information for Blank 1 is the command show ip route.
The missing information for Blank 1 is the command debug ip route.
The missing information for Blank 2 is the number 100.
The missing information for Blank 2 is the number 120.
The missing information for Blank 3 is the letter R.
The missing information for Blank 3 is the letter C.

Refer to the exhibit. The network is using the RIPv2 routing protocol. If network 10.0.0.0 goes down, what mechanism will prevent Router1 from advertising false routing information back to Router2?
triggered updates
poison reverse
holddown timers
split horizon

How does route poisoning prevent routing loops?

New routing updates are ignored until the network has converged.

Failed routes are advertised with a metric of infinity.

A route is marked as unavailable when its Time to Live is exceeded.

The unreachable route is cleared from the routing table after the invalid timer expires.

Refer to the exhibit. R1 and R2 are both configured with RIPv1. Beginning from global configuration mode, what comand or commands will eliminate RIP updates on the Ethernet segment of R2?

R2# configure terminal
R2(config)# router rip
R2(config-router)# passive-interface FastEthernet0/0

R2# configure terminal
R2(config)# passive-interface FastEthernet0/0

R2# passive-interface FastEthernet0/0

R2# configure terminal
R2(config)# interface FastEthernet0/0
R2(config-if)# passive-interface FastEthernet0/0


Refer to the exhibit. All routers are configured with RIPv2 active on all interfaces. Automatic summarization is in effect. Why does the routing table on R3 include the 209.165.200.228/30 network but not the 172.30.1.0/24 and 172.30.2.0/24 networks?
CIDR is required to route supernets.
There is no default gateway configured.
The 172.30.0.0/16 subnets are discontiguous.
RIPv2 cannot route networks with variable subnets.

Refer to the exhibit. The routers in the exhibit are running the EIGRP routing protocol. What statement is true regarding how packets will travel from the 172.16.1.0/16 network to the 192.168.200.0/24 network?
The router chooses the first path that it learned and installs only that route in the routing table.
The router chooses the path with the lowest administrative distance and installs only that route in the routing table.
The router chooses the highest routing ID based on the advertised network IP addresses and installs only that route in the routing table.
The router installs all the equal cost paths in the routing table but sends packets out only one, holding the others in reserve in case the primary route goes down.
The router installs all the equal cost paths in the routing table and performs equal cost load balancing to send packets out multiple exit interfaces.

Refer to the exhibit. Which two statements are true based on the exhibited output? (Choose two.)
All routes are stable.
Each route has one feasible successor.
The serial interface between the two routers is down.
The administrative distance of EIGRP has been set to 50.
The show ip eigrp topology command has been run on R1.

Refer to the exhibit. Host A is having problems accessing server A. All routers have the same EIGRP configuration as router RTR_A. What should be done so that host A can access server A?
Add the command no auto-summary on all routers.
Change the network statements to include a wildcard mask.
Adjust the EIGRP hello timers to account for the network delay.
Add the command eigrp log-neighbor-changes on all routers.

When would the network administrator use the ip bandwidth-percent eigrp as-number percent command?

when there is a low bandwidth connection

when the connection is on a shared medium

when the connection is serial instead of Ethernet

when the link is always busy


Refer to the exhibit. What information can be determined from the displayed output?
EIGRP packets are waiting to be sent to the neighbors.
The adjacencies between the routers are yet to be established.
The IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2.
Router R2 is receiving hello packets from a neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interface.

Refer to the exhibit. What will happen if interface Serial0/0/1 goes down on Router1?
The Dijkstra algorithm will calculate the feasible successor.
DUAL will query neighbors for a route to network 192.168.1.0.
Neighbor 172.16.3.2 will be promoted to the feasible successor.
Traffic destined to the 192.168.1.0 network will be dropped immediately due to lack of a feasible successor.

Which statement correctly describes a feasible successor in EIGRP?

It is a primary route that is stored in the routing table.

It is a backup route that is stored in the routing table.

It is a primary route that is stored in the topology table.

It is a backup route that is stored in the topology table.


Refer to the exhibit. A network administrator is trying to determine why router JAX has no OSPF routes in its routing table. All routers are configured for OSPF area 0. From the JAX router, the administrator is able to ping its connected interfaces and the Fa0/1 interface of the ORL router but no other router interfaces. What is a logical step that the network administrator should take to troubleshoot the problem?
Reboot the routers.
Change the OSPF process ID on all of the routers to 0.
Check to see if the cable is loose between ORL and JAX.
Check to see if CDP packets are passing between the routers.
Use show and debug commands to determine if hellos are propagating.
Which of the following are required when adding a network to the OSPF routing process configuration? (Choose three.)
network address
loopback address
autonomous system number
subnet mask
wildcard mask
area ID

Refer to the exhibit. R1 and R2 are unable to establish an adjacency. What two configuration changes will correct the problem? (Choose two.)
Set a lower priority on R2.
Configure the routers in the same area.
Set a lower cost on R2 compared to R1.
Add a backup designated router to the network.
Match the hello and dead timers on both routers.

A network administrator is analyzing routing update behavior on a network that has both EIGRP and OSPF configured on all routers. Both protocols appear in the output of show ip protocols. However, only EIGRP internal routes appear in the routing tables. Which statement correctly explains the scenario?

The OSPF protocol has a higher cost than EIGRP.

The EIGRP protocol has a lower metric than OSPF.

The EIGRP protocol was configured first on the router.

The EIGRP protocol has a lower administrative distance than OSPF.


Refer to the exhibit. All routers are configured for OSPF area 0. The network administrator requires that R2 always be the DR and maintain adjacency.

Which two configurations can achieve this? (Choose two.)
Change the OSPF area of R2 to a higher value.
Change the router ID for R2 by assigning the IP address 172.16.30.5/24 to
the Fa0/0 interface.
Change the priority values of the Fa0/0 interfaces of R1 and R3 to 0.
Configure a loopback interface on R2, with an IP address higher than any IP
address on the other routers.
Configure R1 and R3 with an IP address whose value is higher than that of R2.


Refer to the exhibit. A network administrator has configured OSPF using the following command:

network 192.168.1.32 0.0.0.31 area 0

Which router interface will participate in OSPF?


FastEthernet0/0

FastEthernet0/1

Serial0/0/0

Serial0/0/1

Which two statements are true for OSPF Hello packets? (Choose two.)
They are used for dynamic neighbor discovery. They are used to maintain neighbor relationships.
They are used to determine the complete network topology.
They are used with timers to elect the designated router with the fastest link.
They are used to negotiate correct parameters among neighboring interfaces.

Tags:

Related Posts

CCNA 1 2011 CCNA 2 2011 CCNA 3 2011 CCNA 4 2011
Copyright © 201

Saturday, May 7, 2011

CCNA 3 Exploration V4 Module 4 Exam 100% new Update

CCNA 3 Exploration V4 Module 4 Exam 100% new Update



CCNA 3 Exploration V4 Module 4 Exam 100% new Update

1. Refer to the exhibit. Switch1 is not participating in the VTP management process with the other switches shown in the exhibit. What are two possible reasons for this? (Choose two.)
Switch2 is in transparent mode.
Switch1 is in client mode.
• Switch1 is using VTP version 1 and Switch2 is using VTP version 2.
Switch2 is in server mode.
• Switch1 is in a different management domain.
Switch1 has no VLANs.

2. Refer to the exhibit. Switches SW1 and SW2 are interconnected via a trunk link but failed to exchange VLAN information. The network administrator issued the show vtp status command to troubleshoot the problem. On the basis of the output provided, what could be done to fix the problem?
The switches must be interconnected via access link.
Switch SW2 must be configured as a VTP client.
Both switches must be configured as VTP clients.
Both switches must be configured with the same VTP revision number.
• The switches must be configured with the same VTP domain name.

3. Refer to the exhibit. Which two facts can be confirmed by this output? (Choose two.)
• If this switch is added to an established network, the other VTP-enabled switches in the same VTP domain will consider their own
• VLAN information to be more recent than the VLAN information advertised by this switch.
This switch shows no configuration revision errors.
This switch has established two-way communication with the neighboring devices.
This switch is configured to advertise its VLAN configuration to other VTP-enabled switches in the same VTP domain.
This switch is configured to allows the network manager to maximize bandwidth by restricting traffic to specific network devices.

4. Which two statements describe VTP transparent mode operation? (Choose two.)
Transparent mode switches can create VLAN management information.
• Transparent mode switches can add VLANs of local significance only.
• Transparent mode switches pass any VLAN management information that they receive to other switches.
Transparent mode switches can adopt VLAN management changes that are received from other switches.
Transparent mode switches originate updates about the status of their VLANS and inform other switches about that status.

5. Refer to the exhibit. Switch2 was previously used in a lab environment and has been added to the production network in server mode. The lab and production networks use the same VTP domain name, so the network administrator made no configuration changes to Switch2 before adding it to the production network. The lab domain has a higher revision number. After Switch2 was added to the production network, many computers lost network connectivity. What is the quickest way to solve the problem?
Reset the revision number on Switch2 with either the delete VTP command or by changing the domain name and then changing it back.
Change Switch1 to transparent VTP mode to reclaim all VLANs in vlan.dat, and then change back to server mode.
Change Switch2 to client mode so the VLANs will automatically repopulate.
• Re-enter all appropriate VLANs, except VLAN 1, manually on Switch1 so that they repropagate throughout the network.

6. What causes a VTP configured switch to issue a summary advertisement?
A new host has been attached to a switch in the management domain.
A port on a switch in the management domain has changed to blocking mode.
• A five-minute update timer has elapsed.
The advertisement revision number has reached n+1.

7. Which two statements describe VTP client mode operation. (Choose two.)
• can add VLANs of local significance only
can only adopt VLAN management changes
• can create and adopt updated VLAN management information
can only pass VLAN management information without adopting changes
can add VLANs to domain
cannot add VLANs

8 Which statement is true when VTP is configured on a switched network that incorporates VLANs?
VTP is only compatible with the 802.1Q standard.
VTP adds to the complexity of managing a switched network.
A switch configured for VTP can belong to more than one VTP domain.
• VTP dynamically communicates VLAN additions, deletions and modifications to all switches in the same VTP domain.
VTP advertisements are passed over access links to other switches.

9. Refer to the exhibit. All switches in the VTP domain are new. Switch SW1 is configured as a VTP server, switches SW2 and SW4 are configured as VTP clients, and switch SW3 is configured in VTP transparent mode. Which switch or switches receive VTP updates and synchronize their VLAN configuration based on those updates?
All switches receive updates and synchronize VLAN information.
Only switch SW2 receives updates and synchronizes VLAN information.
• SW3 and SW4 receive updates, but only switch SW4 synchronizes VLAN information.
Only switches SW3 and SW4 receive updates and synchronize VLAN information.

10. Refer to the exhibit. What information can be learned from the output provided?
It verifies the configured VTP password.
It verifies the VTP domain is configured to use VTP version 2.
• It verifies VTP advertisements are being exchanged.
It verifies the VTP domain name is V1.

11. Which statement is true about the VTP pruning process?
VTP pruning automatically updates all switches within the VTP domain with VLAN information.
VTP pruning updates all switches within the VTP domain with information about pruning-eligible VLANs.
VTP pruning updates all switches within the VTP domain with information about pruning-ineligible VLANs.
• VTP pruning prevents flooded traffic from crossing trunk links to switches that do not need to process the flood traffic.

12. Refer to the exhibit. The switches in the exhibit are connected with trunks within the same VTP management domain. Each switch is labeled with its VTP mode. A new VLAN is added to Switch3. This VLAN does not show up on the other switches. What is the reason for this?
VLANs cannot be created on transparent mode switches.
Server mode switches neither listen to nor forward VTP messages from transparent mode switches.
• VLANs created on transparent mode switches are not included in VTP advertisements.
There are no ports assigned to the new VLAN on the other switches.
Transparent mode switches do not forward VTP advertisements.

13. What does a client mode switch in a VTP management domain do when it receives a summary advertisement with a revision number higher than its current revision number?
It suspends forwarding until a subset advertisement update arrives.
• It issues an advertisement request for new VLAN information.
It increments the revision number and forwards it to other switches.
It deletes the VLANs not included in the summary advertisement.
It issues summary advertisements to advise other switches of status changes.

14. Which three VTP parameters must be identical on all switches to participate in the same VTP domain? (Choose three.)
revision number
• domain name
pruning
mode
• domain password
• version number

15. Refer to the exhibit. All switches in the network participate in the same VTP domain. What happens when the new switch SW2 with a default configuration and revision number of 0 is inserted in the existing VTP domain Lab Network?
The switch operates as a VTP client.
switch operates in VTP transparent mode.
• The switch operates as a VTP server and deletes the existing VLAN configuration in the domain.
The switch operates as a VTP server, but does not impact the existing VLAN configuration in the domain.

16. Refer to the exhibit. Switch S1 is in VTP server mode. Switches S2 and S3 are in client mode. An administrator accidentally disconnects the cable from F0/1 on S2. What will the effect be?
S2 loses all VLANs until the cable is reconnected.
S2 automatically transitions to VTP transparent mode.
• S2 does not send a VTP request advertisement unless it is reloaded.
S2 automatically sends a VTP request advertisement to 172.17.99.11 when the cable is reconnected.

17. Which two statements are true about the implementation of VTP? (Choose two.)
• Switches must be connected via trunks.
• The VTP domain name is case sensitive.
Transparent mode switches cannot be configured with new VLANs.
The VTP password is mandatory and case sensitive.
Switches that use VTP must have the same switch name.

Friday, May 6, 2011

The Scoop on the New CCNA and CCNP Specializations

The Scoop on the New CCNA and CCNP Specializations

Author: John Pherson

Abstract

There has been a lot of interest among students lately on the details surrounding the CCNA specializations and their relationship with the corresponding CCNP specializations. These specializations were introduced in the summer of 2008. The purpose of this white paper is to put all the related information into one concise reference document.

Introduction

The CCNA specializations were introduced by Cisco to provide a way of recognizing associate-level expertise in particular technology areas. They are also designed to provide a stepping-stone to the pursuit of professionallevel specializations. Recognizing that the one-size-fits-all approach may not meet the needs of students with an interest in a particular technology area, as well as the needs of enterprises for specialized knowledge in implementing and supporting these areas, Cisco has introduced the following specialties.

  • CCNA Wireless and CCNP Wireless
  • CCNA Voice and CCVP (Cisco Certified Voice Professional)
  • CCNA Security and CCSP (Cisco Certified Security Professional)

The foundation for each of these certifications is the basic CCNA certification, which can involve passing either the comprehensive CCNA exam (640-802) or both the CCENT exam (640-822), which tests content from the ICND1 course, and the (640-816) exam covering content from ICND2.

The preparation for these exams involves attending either

ICND1 5 days GK Course # 5085

And

ICND2 5 days GK Course # 5090

Or, for more experienced students

CCNA Boot camp 5 extended days GK Course # 5031

The following sections will outline the details of each of the specializations.

Wireless

CCNA Wireless

To achieve the CCNA Wireless certification, there is one additional test required, and one additional course recommended for preparation.

Test: 640-721 Implementing Unified Wireless Networking Essentials

Course: IUWNE 5 days GK Course # 5999

This five-day course introduces wireless topics such as standards bodies, RF principles, configuration of wireless access points and controllers, wireless security, configuring wireless clients, troubleshooting, and the use of management tools such as the WCS (Wireless Control System). It is focused primarily on Cisco's Lightweight Access Point technology, but also discusses the autonomous access points as well.

The CCNA Wireless certification is required as a pre-requisite for attaining the CCNP wireless specialization.

CCNP Wireless

The tests and corresponding courses for this certification are as follows.

Test: 642-731 Conducting Cisco Unified Wireless Site Survey

Course: CUWSS 5 days GK Course # 5904

Test: 642-741 Implementing Cisco Unified Wireless Voice Networks

Course: IUWVN 5 days GK Course # 5901

Test: 642-746 Implementing Cisco Unified Mobility Services

Course: IUWMS 5 days GK Course # 5902

Test: 642-736 Implementing Advanced Cisco Unified Wireless Security

Course: IAUWS 5 days GK Course # 5903

Voice

CCNA Voice

As of June 2009, Cisco announced two options for completion of the CCNA Voice certification. The first is called the Commercial option and is positioned as a standalone certification for implementing VoIP in Small- and Medium-Sized enterprises, typically less than 2000 users. The second is called the Enterprise option, and designed for students who wish to focus on voice solutions for larger environments involving the Cisco Unified Communications Manager.

The CCNA Voice Commercial specialization requires a valid CCNA certification plus one additional test. There is also a 5-day course available to provide preparation for this test.

Test: 640-460 Implementing Cisco IOS Unified Communications

Course: IIUC 5 days GK Course # 5711

The target of the 5-day IIUC course is small business and small site implementations. As such, it provides some fundamentals in VoIP technology, as well as PST N topics, but the product focus is on the Cisco Unified Communications 500 Series of appliances for small business, and the Cisco Unified Communications Manager Express product that runs on an integrated services router (ISR). It also includes an introduction to Unity Express, a small-scale, router-based solution for unified messaging.

The Enterprise option involves obtaining a valid CCNA certification, and then passing the CCVP test for CVoice (642-436). This is probably a better option for students who are either working primarily in Unified Communications Manager environments, or else planning to continue on to the CCVP certification. Passing the CVoice test will satisfy both the requirement for CCNA Voice, as well as counting towards one of the tests required for CCVP.

Tuesday, March 8, 2011

640-802 CCNA® EXAM

Exam Number:640-802 CCNA
Associated Certifications:CCNA
Duration:90 minutes (45-55 questions)
Available Languages:English, Japanese, Chinese*, Spanish, Russian*, Korean*, French, Portuguese
Click Here to Register:Pearson VUE
Exam Policies:Read current policies and requirements
Exam Tutorial:Review type of exam questions
Register for Courses:ICND1 and ICND2 courses and other offerings

Exam Description

The 640-802 CCNA is the composite exam associated with the Cisco Certified Network Associate certification. Candidates can prepare for this exam by taking the Interconnecting Cisco Networking Devices Part 1 (ICND1) v1.1 and the Interconnecting Cisco Networking Devices Part 2 (ICND2) v1.1 courses. This exam tests a candidate's knowledge and skills required to install, operate, and troubleshoot a small to medium size enterprise branch network. The topics include connecting to a WAN; implementing network security; network types; network media; routing and switching fundamentals; the TCP/IP and OSI models; IP addressing; WAN technologies; operating and configuring IOS devices; extending switched networks with VLANs; determining IP routes; managing IP traffic with access lists; establishing point-to-point connections; and establishing Frame Relay connections.

Exam Topics

The following topics are general guidelines for the content likely to be included on the Cisco Certified Network Associate exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice.

640-802 CCNA Exam Topics

Recommended Training

  • Interconnecting Cisco Networking Devices Part 1 (ICND1) v1.1

and

  • Interconnecting Cisco Networking Devices Part 2 (ICND2) v1.1

Courses listed are the recommended training for this exam and are offered by Cisco Learning Partners, the only authorized source for Cisco IT training delivered exclusively by Certified Cisco Instructors. Check the Global Learning Partner Locator for a Cisco Learning Partner near you.

Additional Resources

A variety of Cisco Press titles may be available for this exam. These titles can be purchased through the Cisco Marketplace Bookstore, or directly from Cisco Press

The Cisco® Networking Academy® Program is pleased
to announce the next generation of the Cisco CCNA®
curricula. These curricula were designed to address a
changing marketplace and respond to input from administrators,
instructors, and students.
New features of the next-generation curricula include
embedded “e-Doing,” which uses the capabilities of a
computer to provide guidance and opportunities for
exploration and experimentation; enhanced instructional
features; and an updated graphical user interface (GUI).
In addition, they allow for more efficient translation to
support Cisco’s commitment to delivering the curricula
in multiple languages.
Studies around the world show a gap between the IT
jobs available and qualified candidates to fill them. The
Networking Academy program educates the architects of
the networked economy by providing students with the
skills needed to succeed in the wide range of careers
available today and in the future.
New Curricula Description
Two separate curricula were created so that instructors
can more easily and effectively teach CCNA concepts to
students at different skill levels:
CCNA for advanced learning (CCNA-A*) offers
students in-depth theory, challenging labs, and
detail around protocol operation. It prepares
students to be successful IT professionals in
small-to-medium businesses as well as enterprise
and service provider environments. CCNA-A was
designed to be part of an integrated curriculum or
continuing education program at postsecondary
institutions; typically career and technical schools,
colleges, and universities. CCNA-A is for students
•
with advanced problem-solving and analytical skills,
such as students who are pursuing degrees in engineering,
math, or science.
CCNA for foundational learning (CCNA-B*) provides
a hands-on approach to learning networking skills. It
uses easy-to-follow labs to help students learn the
general theory needed to build networks. CCNA-B
allows for quick application of learned concepts
to encourage students to consider additional
education in IT and helps prepare students for
entry-level IT careers by teaching applied skills
midway through the four-course series. CCNA-B
was designed to be delivered as an independent
curriculum or possibly integrated into a broader
course of study at upper-secondary institutions,
career and technical schools, and colleges. It is for
students with basic PC usage skills.
* Please note that these are not the official names of
the new curricula. Formal names will be communicated
when the new curricula becomes available.
Why Did We Create Two New Curricula
for CCNA?
Both CCNA-A and CCNA-B prepare students for the
CCNA certification, but in different ways. By using different
teaching methodologies for different types of
students, we can help ensure their success in learning
the content. And since these curricula are targeted
for different educational backgrounds and interests,
students will be more successful in achieving their goals.
This will help improve both student and instructor satisfaction
and help increase enrollment rates.
CCNA-B maps to everyday experiences with networks
and is organized around the types of work environments
• students may encounter, such as a home or small office,
and provides applied skills early in the curriculum.
CCNA-A goes into more technical depth and uses engineering
concepts and terminology.
Advantages of the New CCNA Curricula
Both CCNA-A and CCNA-B offer many new features,
including the following:
Improved accuracy and flow of information, with
less redundancy
Optimal balance of theory, practice, and application
Enhanced and embedded simulation tool for
e-Doing, which provides guidance and opportunities
for exploration and experimentation
Design supporting more efficient localization
High- and low-bandwidth delivery capabilities
Alignment of learning objectives with job skills
Increased use of rich media for ongoing interactivity
throughout the learning process
Who Should Consider Adopting the CCNA-A
Curriculum?
Academies with students who prefer a challenging,
theoretical, and integrated approach typically used at
higher-education institutions should consider adopting
CCNA-A, which has the following features:
Designed for students with advanced problemsolving
and analytical skills, such as students who
are pursuing degrees in engineering, math, or
science
Can be part of an integrated curriculum or continuing
education program at postsecondary
institutions, such as career and technical schools,
colleges, and universities

The New Cisco CCNA Curricula At-A-Glance

Includes highly complex and challenging
hands-on labs
Presents an integrated and comprehensive
coverage of networking topics, from fundamentals
to advanced applications and services
Allows for a preview of the strategic direction of
networking by providing an early introduction to
advanced technologies, converged networked
applications, and the services that networks provide
to those applications
Organizes topics to allow for flexibility in the order
and delivery of the courses
Builds deeper conceptualizations, connections, and
technology language that will integrate with other
engineering concepts
Who Should Consider Adopting the CCNA-B
Curriculum?
The CCNA-B curriculum is primarily designed for
Academies with students looking for career-oriented,
IT-skills instruction or a quick path to job entry and career
exploration. The CCNA-B curriculum has the following
features:
Designed for students with basic PC skills
Can be delivered as an independent curriculum
or integrated into broader course studies at
upper-secondary institutions, career and technical
schools, and colleges

Offers a hands-on, career-oriented approach to
learning networking that emphasizes practical
experience
Maps more directly to everyday experiences with
networks and covers key networking concepts
according to the types of practical network environments
students may encounter; ranging from small
office or home office (SOHO) networking to more
complex enterprise and theoretical networking
models later in the curriculum
Includes activities that emphasize the implementation
of networking
Teaches applied skills midway through the fourcourse
series to help make IT relevant, encourage
students to consider additional education in IT, and
help students prepare for entry-level IT careers
Availability
The English versions of CCNA-A courses 1 and 2 and
CCNA-B courses 1 and 2 will be available in the June–
August 2007 timeframe. The English versions of CCNA-A
courses 3 and 4 and CCNA-B courses 3 and 4 will be
available in the November–December 2007 timeframe.
The current CCNA curriculum will continue to be made
available as long as it aligns with customer needs and
certification requirements.
Cisco is committed to translating the new CCNA
curricula into other languages. Information about the

translating that will be performed by Cisco will be
announced in the June–August 2007 timeframe.
Why Choose the Cisco Networking Academy
Program?
As the worldwide leader in networking for the Internet,
Cisco is uniquely qualified to help educate the next
generation of IT professionals. Education delivery also
supports Cisco’s culture of giving back to the community.
The Networking Academy program uses a combination
of face-to-face training with online curricula, hands-on
lab exercises, realistic network simulation, and an
Internet-based assessment tool to deliver standardsbased
content.
By using our innovative networking technology and
communications expertise to deliver IT education, we
can help improve global communities, especially those
that are underserved. Cisco founded the Networking
Academy program to help foster access to education
and professional opportunities worldwide. Since its
creation in 1997, approximately two million students have
enrolled at more than 10,000 Academies in more than
160 countries; creating a global community of instructors
and students.
The New Cisco CCNA Curricula At-A-Glance
Copyright © 2006 Cisco Systems, Inc. All rights reserved. CCNA, Cisco, Cisco Systems, the Cisco Systems logo, and Networking Academy are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
C45-379772-00 11/06

Saturday, January 15, 2011

Cisco 4500

This document describes how to configure a management IP address on Catalyst 4500/4000, 5500/5000, and 6500/6000 series switches that run Catalyst OS (CatOS) and Cisco IOS® Software. This document also includes Catalyst fixed configuration switches, which run Cisco IOS Software only and include the 2900/3500XL, 2940, 2950, 2955, 2970, 3550, and 3750 series switches. An IP address is necessary if you want to manage the switch from a remote TCP/IP capable management station. A switch that is to be managed by a VT100 terminal on its console port does not require an IP address.

Prerequisites

Requirements

Cisco recommends that you have knowledge of the information in this section.

Catalyst 4500/4000, 5500/5000, 6500/6000 switches that run only CatOS are Layer 2 (L2) switches. The Catalyst fixed configuration switches 2900/3500XLs, 2940, 2950, 2955, and 2970 are also L2 switches. The TCP/IP protocol on an L2 switch is for management purposes only. Data that flows through the switch can have Layer 3 (L3) addresses, such as IP, Internetwork Packet Exchange (IPX), AppleTalk, and so on. However, the switch uses only the data MAC address in order to determine from where traffic has come and which ports should receive the data. L2 switches ignore L3 addresses when the switches forward data.

The Catalyst 6500/6000, 4500/4000, and 3550/3750 series switches that run Cisco IOS Software are switch routers or L3 switches, and can use any interface for management. You can configure the management interface in any of these ways:

  • As a logical interface, like a loopback interface

  • As an L2 access port in a management VLAN

  • As an L3 interface with an IP address

    Note: This is the same way in which you configure the interface on any Cisco router.

The Catalyst switches that this document discusses have these management interfaces:

  • Catalyst 5500/5000 and 6500/6000 series switches with Supervisor Engines that run CatOS have two configurable IP management interfaces:

    • The in-band (sc0) interface

    • The Serial Line Internet Protocol (SLIP) (sl0) interface

  • Catalyst 4500/4000 switches with Supervisor Engines that run CatOS have three configurable IP management interfaces. The additional interface is called the management Ethernet (me1) interface.

  • Catalyst L2 fixed configuration switches that run Cisco IOS Software have only one configurable IP management interface, which by default is interface VLAN 1.

  • Pure layer 2 switches can have only one interface VLAN up at the time. This is called the management VLAN (in IOS) or the sc0 interface (in CatOS). The main purpose of this interface is management (telnet, SNMP, etc). If the switch is a Layer 3 switch, you can configure multiple VLANs and route between them. An L3 switch can handle multiple IPs, so there is no specific management VLAN on the switch.

  • Catalyst 3550/3750 series switches that run Cisco IOS Software can use any interface for management.

Components Used

This document is not restricted to specific software and hardware versions.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

Catalyst 4500/4000, 5500/5000, and 6500/6000 Management Interfaces

The sc0 interface is an internal management interface connected to the switching fabric. The sc0 interface participates in all the functions of a normal switch port, which include:

  • Spanning Tree Protocol (STP)

  • Cisco Discovery Protocol (CDP)

  • Virtual LAN (VLAN) membership

The me1 and sl0 interfaces are out-of-band management interfaces that are not connected to the switching fabric and do not participate in any of these functions.

When you configure the IP address, subnet mask, and broadcast address (and, on the sc0 interface, VLAN membership) of the sc0 or me1 interface, you can access the switch through Telnet or Simple Network Management Protocol (SNMP). When you configure the SLIP (sl0) interface, you can open a point-to-point connection to the switch through the console port from a workstation.

If you have the output of a show interface command from your Cisco device, you can use the Output Interpreter (registered customers only) tool to display potential issues and fixes.

The sc0 does not have an external port for direct connection. This interface exists as a logical interface inside the switch and is accessible through any of the physical ports on the switch. This figure provides an illustration:

8a.gif

The me1 is actually a physical Ethernet port on the Supervisor Engine module on the Catalyst 4500/4000 series switches. This interface is used for network management only and does not support network switching.

8d.gif

The sl0 uses the RS232 console port as its physical interface. The sl0 cannot be used as a VT100 console when it is in SLIP mode. This figure illustrates a SLIP connection to sl0:

8b.gif

Configure the sc0 Interface on Catalyst 4500/4000, 5500/5000, and 6500/6000 Switches That Run CatOS

This section describes how to configure an IP address on the in-band sc0 interface.

  1. Connect a terminal to the console ports of the switches.

    For details on how to connect to the console ports of the Catalyst switches, refer to Connecting a Terminal to the Console Port on Catalyst Switches.

  2. Issue the show interface command at the switch prompt in order to view the default status of the management interfaces.

    Switch-A> (enable) show interface
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    !--- Catalyst 5500/5000 and 6500/6000 series switches
    !--- do not display the me1 interface in the output.


    Switch-A> (enable)
  3. Issue the set interface sc0 172.16.84.17 255.255.255.0 172.16.84.255 command in order to configure an IP address for sc0.

    The message that the switch returns tells you which parameters have been changed.

    Note: When you issue the set interface sc0 command, you cannot enter the broadcast address without the subnet mask of the IP address.

    Switch-A> (enable) set interface sc0 172.16.84.17 255.255.255.0 172.16.84.255 
    
    Interface sc0 IP address, netmask, and broadcast set.
    Switch-A> (enable)

    Issue the show interface command in order to view the changes.

    Switch-A> (enable) show interface 
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 172.16.84.17 netmask 255.255.255.0 broadcast 172.16.84.255
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    Switch-A> (enable)

    If you enter only an IP address after the set interface sc0 172.16.84.17 command, the default mask and the default broadcast address for the address class are automatically configured. Here is an example:

    Switch-A> (enable) set interface sc0 172.16.84.17
    

    !--- Notice that neither the mask nor the broadcast address is specified.

    Interface sc0 IP address and netmask set.
    Switch-A> (enable)
    Switch-A> (enable) show interface
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 172.16.84.17 netmask 255.255.0.0 broadcast 172.16.255.255

    !--- Notice that the switch took the default mask
    !--- and the broadcast address of class B.


    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    Switch-A> (enable)

    If you enter the IP address and subnet mask after the set interface sc0 command, the broadcast address for the specific subnet is automatically configured.

  4. In order to change the VLAN on the sc0 interface, issue the set interface sc0 vlan# command, which specifies the VLAN number.

    Note: By default, the sc0 interface belongs to VLAN 1.

    If you want to change the membership of sc0 to VLAN 2, issue this command:

    Switch-A> (enable) set interface sc0 2 
    


    Interface sc0 vlan set.
    Switch-A> (enable)

    Note: Be sure that you have configured VLAN 2 on the switch before you issue this command. The configuration of VLANs on Catalyst switches is beyond the scope of this document. For more information, refer to Creating Ethernet VLANs on Catalyst Switches.

    Issue the show interface command in order to view the changes.

    Switch-A> (enable) show interface
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 2 inet 172.16.84.17 netmask 255.255.255.0 broadcast 172.16.84.255
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    Switch-A> (enable)
  5. Issue the show ip route command.

    Note: If you want to be able to manage the switch through a router, you must configure a default gateway. The switch does not participate in IP routing. Therefore, the switch has no knowledge of the L3 topology of the network.

    When you issue the show ip route command, notice that the gateway for the subnet sc0 is assigned to its own address.

    Switch-A> (enable) show ip route 
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    172.16.84.0 172.16.84.17 0xffffff00 U 395 sc0
    default default 0xff000000 UH 0 sl0
    Switch-A> (enable)
  6. Issue the set ip route 0.0.0.0 172.16.84.1 command or the set ip route default 172.16.84.1 command in order to establish the default route.

    The second IP address is the directly connected router that will be your path through the rest of the network. This IP address must be part of the same IP subnet as the switch. You can define up to three default IP gateways. Use the primary keyword with the set ip route command in order to make a gateway the primary gateway. If you do not specify a primary default gateway, the first gateway that is configured is the primary gateway. If more than one gateway is designated as primary, the last primary gateway that is configured is the primary default gateway.

    • Switch-A> (enable) set ip route 0.0.0.0 172.16.84.1 
      
      Route added.
      Switch-A> (enable)

    or

    • Switch-A> (enable) set ip route default 172.16.84.1
      
      Route added.
      Switch-A> (enable)

    Issue the show ip route command in order to view the changes.

    Switch-A> (enable) show ip route 
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 172.16.84.1
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 172.16.84.1 0x0 UG 0 sc0
    172.16.84.0 172.16.84.17 0xffffff00 U 525 sc0
    default default 0xff000000 UH 0 sl0
    Switch-A> (enable)
  7. If you need to clear the routes from the routing table, issue the clear ip route all command.

    Note: If you are connected to the switch through Telnet from a different subnet, you lose connection when you clear the routes. You cannot reach the switch again until someone reenters the gateway address through an attached console or a PC/terminal that is on the same subnet as the switch.

    Switch-A> (enable) clear ip route all
    
    All routes deleted.
    Switch-A> (enable)

    You can clear a single route if you specify only that route. Issue the clear ip route 0.0.0.0 172.16.84.1 command.

Configure the SLIP (sl0) Interface on Catalyst 4500/4000, 5500/5000, and 6500/6000 Switches That Run CatOS

You can use a SLIP connection over sl0 in order to monitor or manage the switch remotely with a TCP/IP-capable device where there is no other path to the switch except through the console port.

A network manager can use a remote PC to dial up switches anywhere in the world and manage the switches with the use of SNMP or Telnet over SLIP. You can also upload system software over the sl0 interface with the use of TFTP. Without SLIP, the console port can only be used for VT100 access (tty) or Kermit file transfers. Refer to Connecting a Modem to the Console Port on Catalyst Switches for more information on how to enable dialup connectivity to a Catalyst switch.

This figure shows an example of the management of a switch by a remote terminal with the use of sl0. This type of management is sometimes referred to as out-of-band management. Out-of-band means that a management terminal accesses the device through a path that does not include the network to which the switch is connected.

8c.gif

If you set up and activate the sl0 interface from a directly attached console terminal, you lose your console connection. If the terminal that you use supports SLIP, establish a SLIP session with the switch. Deactivate the SLIP connection when you finish in order to allow direct console connectivity. If you activate SLIP and your terminal does not support SLIP, you must establish a Telnet connection to the switch and deactivate sl0 or power cycle the switch in order to regain access to the console port.

Note: Unless you have a terminal that can run SLIP and you know how to use it, only perform these steps from a Telnet connection to the switch.

  1. Establish a Telnet session to the switch.

  2. Issue the set interface sl0 1.1.1.1 1.1.1.2 command at the command prompt in order to set the SLIP address of the switch and the destination IP address.

    Here is an example:

    Switch-A> (enable) set interface sl0 1.1.1.1 1.1.1.2
    
    Interface sl0 slip and destination address set.
    Switch-A> (enable)
  3. Issue the slip attach command at the command prompt in order to activate SLIP mode.

    Here is an example:

    Switch-A> (enable) slip attach
    
    Console Port now running SLIP.
    Switch-A> (enable)
  4. Issue the slip detach command at the command prompt in order to deactivate SLIP mode.

    Here is an example:

    Switch-A> (enable) slip detach
    
    SLIP detached on Console port.
    Switch-A> (enable)

Configure the Management Ethernet Interface (me1) on a Catalyst 4500/4000 That Runs CatOS

This section explains how to configure an IP address on the me1 that is present on the Catalyst 4500/4000 series switches. Packets received on the me1 interface never reach the switching fabric, and there is no access to the me1 interface except through the Ethernet port on the Supervisor Engine.

Another characteristic of the me1 interface is that, when the switch is in ROM monitor (ROMmon), interface me1 is the only interface that is active. You can boot from the network through me1 or upgrade the Cisco IOS Software through me1 while in ROMmon. However, you must be directly on the console port. You can use this interface when you recover a Catalyst 4500/4000 series switch from a corrupted or missing software image or from an upgrade failure. For those details, refer to the Recovering the Catalyst 4000, Catalyst 2948G, Catalyst 2980G, and Catalyst 4912G section of Recovering Catalyst Switches Running CatOS from Booting Failures.

You configure the IP address on the me1 interface in a way that is similar to the configuration on the sc0 interface. The only difference is that you cannot attach the me1 interface to any VLAN because this interface does not reach the switching fabric as the sc0 interface does.

Complete these steps in order to configure an IP address on the me1 interface:

  1. Connect a terminal to the console port of the switch.

  2. Issue the show interface command at the switch prompt in order to view the default status of the me1 interface.

    Here is an example:

    Switch-A> (enable) show interface
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    Switch-A> (enable)
  3. Issue the set interface me1 10.1.1.2 255.255.255.0 10.1.1.255 command in order to configure an IP address for me1.

    The message that the switch returns tells you which parameters have been changed.

    Note: You must enter a netmask in order to configure a broadcast address.

    Switch-A> (enable) set interface me1 10.1.1.2 255.255.255.0 10.1.1.255
    
    Interface me1 IP address, netmask, and broadcast set.
    Switch-A> (enable)

    Issue the show interface command in order to view the changes that you have made.

    Switch-A> (enable) show interface
    
    sl0: flags=50
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    me1: flags=63
    inet 10.1.1.2 netmask 255.255.255.0 broadcast 10.1.1.255

    Switch-A> (enable)

    If you enter only an IP address after the set interface me1 10.1.1.2 command, the default mask and the default broadcast address for the address class that you used are configured. Here is an example:

    Switch-A> (enable) set interface me1 10.1.1.2
    

    !--- Notice that neither the mask nor the broadcast address is specified.

    Interface sc0 IP address and netmask set.
    Switch-A> (enable)

    Switch-A> (enable) show interface
    sl0: flags=50
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    me1: flags=63 <UP,BROADCAST,RUNNING>
    inet 10.1.1.2 netmask 255.0.0.0 broadcast 10.255.255.255

    !--- Notice that the switch took the
    !--- default mask and the broadcast address of class A.


    Switch-A> (enable)

    Note: Normally, the me1 interface is configured to be in a different subnet than the sc0 interface, which allows both interfaces to remain up. Both interfaces can be configured in the same subnet or with the same IP address, but the sc0 interface is shut down in this case. Interface me1 always takes precedence in this instance. For example, if you have already configured the sc0 interface with an IP address of 172.16.84.17 255.255.255.0, and you try to configure the me1 interface in the same subnet (172.16.84.18 255.255.255.0), you see these messages:

    Switch-A> (enable) set interface me1 172.16.84.18 255.255.255.0 172.16.80.255
    
    This command places me1 and sc0 into the same ip subnet.
    The sc0 interface will be automatically configured down if necessary to resolve
    the conflict.
    Do you want to continue (y/n) [n]?y
    Interface me1 IP address, netmask, and broadcast set.
    Interface sc0 administratively down due to conflict.
    Console> (enable)

    !--- Check the configuration.

    Switch-A> (enable) show interface
    sl0: flags=50
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=62 <DOWN,BROADCAST,RUNNING>
    vlan 1 inet 172.16.84.17 netmask 255.255.255.0 broadcast 172.16.84.255
    me1: flags=63
    inet 172.16.84.18 netmask 255.255.255.0 broadcast 172.16.84.255
    Switch-A> (enable)
  4. If you noticed in Step 3 that the status of me1 is down instead of up, issue this command in order to bring the interface up manually:

    Switch-A> (enable) set interface me1 up
    
    Interface me1 administratively up.
    Switch-A> (enable)
  5. Issue the show ip route command.

    Note: If you want to be able to manage the switch through a router, you must configure a default gateway because the switch does not participate in IP routing. Therefore, the switch has no knowledge of the L3 topology of the network.

    When you issue the show ip route command, notice that the gateway for the subnet me1 is assigned to its own address.

    Switch-A> (enable) show ip route 
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    10.1.1.0 10.1.1.2 0xffffff00 U 0 me1
    Switch-A> (enable)
  6. Issue the set ip route 0.0.0.0 10.1.1.3 command or the set ip route default 10.1.1.3 command in order to establish the default route.

    The second IP address is the directly connected router that will be your path through the rest of the network. This IP address must be part of the same IP subnet as the switch.

    • Switch-A> (enable)set ip route 0.0.0.0 10.1.1.3
      
      Route added.
      Switch-A> (enable)

    or

    • Switch-A> (enable) set ip route default 10.1.1.3
      
      Route added.
      Switch-A> (enable)

    Issue the show ip route command in order to view the changes.

    Switch-A> (enable) show ip route
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 10.1.1.3
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 10.1.1.3 0x0 UG 0 me1
    10.1.1.0 10.1.1.2 0xffffff00 U 1 me1
    Switch-A> (enable)

    Note: If sc0 and me1 are in different subnets, you can configure multiple default gateways. However, the gateway that is defined first becomes the primary gateway. If this is the gateway that you intend, you must use the keyword primary at the end of the command in order to change the primary default gateway. For example, 172.16.84.1 is the primary gateway in a case in which both these item are true:

    • You have sc0 with IP address 172.16.84.17 255.255.255.0 configured first with the default gateway of 172.16.84.1.

    • You configure me1 with an IP address of 10.1.1.2 255.255.255.0 and with the default gateway of 10.1.1.3.

    You can issue these commands in order to change the primary gateway to 10.1.1.3:

    Switch-A> (enable) show ip route
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 172.16.80.1
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 10.1.1.3 0x0 G 0 me1
    default 172.16.84.1 0x0 UG 11 sc0
    172.16.80.0 172.16.84.17 0xffffff00 U 38 sc0
    10.1.1.0 10.1.1.2 0xffffff00 U 4 me1

    !--- Notice that 172.16.84.1 is the primary default gateway.

    Switch-A> (enable)

    !--- Change the primary default gateway to 10.1.1.3.

    Switch-A> (enable) set ip route default 10.1.1.3 primary
    Primary route changed
    Switch-A> (enable)

    !--- This message displays when the primary gateway is changed:

    %SYS-5-RTE_DEFGATEFROM:Default Gateway switching from 172.16.80.1
    %SYS-5-RTE_DEFGATETO:Default Gateway switching to 10.1.1.3

    !--- Verify the change.

    Switch-A> (enable) show ip route
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 10.1.1.3
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 10.1.1.3 0x0 UG 0 me1
    default 172.16.84.1 0x0 G 11 sc0
    172.16.80.0 172.16.84.17 0xffffff00 U 38 sc0
    10.1.1.0 10.1.1.2 0xffffff00 U 4 me1

    !--- Notice that now the primary default gateway is 10.1.1.3.

  7. If you need to clear the routes from the routing table, issue the clear ip route all command.

    Note: If you are connected to the switch through Telnet from a different subnet, your connection is lost when you clear the routes. You cannot reach the switch again until someone reenters the gateway address via an attached console or a PC/terminal on the same subnet as the switch.

    Switch-A> (enable) clear ip route all
    
    All routes deleted.
    Switch-A> (enable)

    You can clear a single route if you specify only that route. Issue the clear ip route 0.0.0.0 10.1.1.3 command.

Configure a Management Interface for Catalyst 4500/4000 Series Switches That Run Cisco IOS Software

On a Catalyst 4500/4000 Supervisor Engine III/IV that runs Cisco IOS Software, any routable interface can be used for management. There are three options to configure this interface.

Note: The Ethernet management port (labeled 10/100 MGT) on a Supervisor Engine III (WS-X4014) or Supervisor Engine IV (WS-X4515) is used in ROMmon mode only to recover a switch software image that is missing or corrupted. This port is not active during normal switch operation and cannot be used as a management interface.

Option 1—Configure a loopback interface for switch management. There are a few advantages to a loopback interface. A loopback is a virtual interface that is always up. Packets that are routed to the loopback interface are rerouted back to the L3 switch or router and processed locally. IP packets that are routed out the loopback interface but are not destined to the loopback interface are dropped. This means that the loopback interface serves as the null 0 interface also. The loopback interface serves as the router ID for Open Shortest Path First (OSPF) and so on. This example uses loopback 0:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface loopback 0
Switch(config-if)#ip address 10.1.1.1 255.255.255.255

!--- The loopback interface should have a 32-bit subnet mask, which means that
!--- the 10.1.1.1 address is the only destination address in this subnet.


Switch(config-if)#end
Switch#

You must also configure a routing protocol to distribute the subnet that is assigned to the loopback address or create a static route.

Option 2—Configure the interface as an L3 routed interface with an IP address. All interfaces on a Catalyst 4500/4000 switch that runs Cisco IOS Software are L2 by default. Therefore, you need to make any interface that is connected to the rest of the network an L3 routed interface. Issue the no switchport command, and configure the desired IP address. The example provides an illustration. All interfaces are enabled by default, so you do not need to issue the no shutdown command. This example uses Fast Ethernet 5/30:

Switch(config)#interface fastethernet 5/30

Switch(config-if)#no switchport
Switch(config-if)#ip address 11.1.1.1 255.0.0.0

If you issue the show running-config interface fastethernet 5/30 command, this output displays:

Building configuration...

Current configuration : 80 bytes
!
interface FastEthernet5/30
no switchport
ip address 11.1.1.1 255.0.0.0
end

Option 3—Configure an L2 interface as a part of a specific VLAN. Issue the switchport mode access command and the switchport access vlan vlan-id command, and use a corresponding switched virtual interface (SVI) with an IP address.

Note: You must understand the difference between the management VLAN that is used to administer the switch and data VLANs that are used to pass L2 traffic. The management VLAN is an SVI the you create with use of the global interface vlan vlan-id command. Do not confuse this command with the commands that you use to create data VLANs to pass L2 traffic. On Catalyst 6500/6000 series switches that run Cisco IOS Software, you can configure data VLANs from the VLAN database or you can issue the global vlan vlan-id command.

Complete these steps:

  1. Issue these commands:

    Switch(config)#interface vlan 1
    
    Switch(config-if)#ip address 10.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    Note: This example uses VLAN 1 as the management VLAN. VLAN 1 is in the VLAN database by default.

  2. Issue the switchport mode access command under the desired physical interface if you want confirmation that the interface is an access switch port.

    By default, all interfaces are L2 interfaces and are access switch ports in VLAN 1. If you plan to use VLAN 1 as the management VLAN, no configuration is necessary under the interface. But if you want confirmation in the configuration that the interface is indeed an access switch port, you need to use the switchport mode access command.

    This example uses Fast Ethernet 5/32:

    Switch(config)#interface fastethernet 5/32
    
    Switch(config-if)#switchport mode access

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Switch#show run interface fastethernet 5/32
    
    Building configuration...

    Current configuration : 84 bytes
    !
    interface FastEthernet5/32
    switchport mode access
    no snmp trap link-status
    end
  3. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI.

    You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

    Switch(config)#interface vlan 2
    
    Switch(config-if)#ip address 20.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    !--- Configure an interface to access the new management VLAN.

    Switch(config)#interface fastethernet 5/32
    Switch(config-if)#switchport mode access
    Switch(config-if)#switch access vlan 2

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Building configuration...
    
    Current configuration : 110 bytes
    !
    interface FastEthernet5/32
    switchport access vlan 2
    switchport mode access
    end

    In order for the switch to access remote networks, you must have either:

    • A default gateway that is set for the next hop router that is directly connected to the switch

    • A dynamic routing protocol configured

    If you are not routing IP, issue the ip default-gateway ip-address command in order to configure a gateway router IP address. In order to configure dynamic routing, use the router routing_protocol command. Issue the show ip route command in order to view the status of the routing table.

Configure a Management Interface for a Catalyst 6500/6000 Switch That Runs Cisco IOS Software

On a Catalyst 6500/6000 series switch that runs Cisco IOS Software, any routable interface can be used for management. There are three options to configure this interface.

Option 1—Configure a loopback interface for switch management. There are a few advantages to a loopback interface. A loopback is a virtual interface that is always up. Packets that are routed to the loopback interface are rerouted back to the L3 switch or router and processed locally. IP packets that are routed out the loopback interface but are not destined to the loopback interface are dropped. This means that the loopback interface serves as the null 0 interface also. The loopback interface serves as the router ID for OSPF and so on. This example uses loopback 0:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface loopback 0
Switch(config-if)#ip address 10.1.1.1 255.255.255.255

!--- The loopback interface should have a 32-bit subnet mask, which means that
!--- the 10.1.1.1 address is the only destination address in this subnet.


Switch(config-if)#end
Switch#

You must also configure a routing protocol to distribute the subnet that is assigned to the loopback address or create a static route.

Option 2—Configure the interface as an L3 routed interface with an IP address. All interfaces on a Catalyst 6500/6000 switch that runs Cisco IOS Software are L3 by default. All interfaces are enabled by default, so you do not need to issue the no shutdown command. This example uses Fast Ethernet 5/30:

Switch(config)#interface fastethernet 5/30

Switch(config-if)#ip address 11.1.1.1 255.0.0.0

If you issue the show running-config interface fastethernet 5/30 command, this output displays:

Building configuration...

Current configuration : 80 bytes
!
interface FastEthernet5/30
no switchport
ip address 11.1.1.1 255.0.0.0
end

Option 3—Configure an L2 interface as a part of a specific VLAN. Issue the switchport mode access command and the switchport access vlan vlan-id command, and use a corresponding SVI with an IP address.

Note: You must understand the difference between the management VLAN that is used to administer the switch and data VLANs that are used to pass L2 traffic. The management VLAN is an SVI that you create with use of the global interface vlan vlan-id command. Do not confuse this command with the commands that you use to create data VLANs to pass L2 traffic. On Catalyst 6500/6000 series switches that run Cisco IOS Software, you can configure data VLANs from the VLAN database or you can issue the global vlan vlan-id command.

Complete these steps:

  1. Issue these commands:

    Switch(config)#interface vlan 1
    

    !--- Interface VLAN 1 is an SVI.

    Switch(config-if)#ip address 10.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    Note: This example uses VLAN 1 as the management VLAN. VLAN 1 is in the VLAN database by default.

  2. Issue the switchport mode access command under the desired physical interface in order to make the interface an L2 interface in default VLAN 1.

    Note: By default, all interfaces are L3 interfaces.

    This example uses Fast Ethernet 5/32:

    Switch(config)#interface fastethernet 5/32
    
    Switch(config-if)#switchport mode access

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Switch#show run interface fastethernet 5/32
    
    Building configuration...
    Current configuration : 84 bytes
    !
    interface FastEthernet5/32
    switchport mode access
    no snmp trap link-status
    end
  3. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI.

    You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

    Switch(config)#interface vlan 2
    
    Switch(config-if)#ip address 20.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    !--- Configure an interface to access the new management VLAN.

    Switch(config)#interface fastethernet 5/32
    Switch(config-if)#switchport mode access
    Switch(config-if)#switch access vlan 2

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Building configuration...
    
    Current configuration : 110 bytes
    !
    interface FastEthernet5/32
    switchport access vlan 2
    switchport mode access
    end

    In order for the switch to access remote networks, you must have either:

    • A default gateway that is set for the next hop router that is directly connected to the switch

    • A dynamic routing protocol configured

    If you are not routing IP, issue the ip default-gateway ip-address command in order to configure a gateway router IP address. In order to configure dynamic routing, use the router routing_protocol command. Issue the show ip route command in order to view the status of the routing table.

Configure a Management Interface for Catalyst L2 Fixed Configuration Switches

The Catalyst L2 fixed configuration switches run Cisco IOS Software, but are L2-capable switches only. These switches can have only one active management interface at a time. The default management interface is VLAN 1. You cannot delete VLAN 1 on these switches. However, you can create another VLAN interface for management, which the examples in this section demonstrate.

Note: You must understand the difference between the management VLAN that is used to administer the switch and VLANs that are used to pass L2 traffic. The management VLAN is an SVI that you create with use of the global interface vlan vlan-id command. Do not confuse this command with the commands that you use to create data VLANs to pass L2 traffic. On XL series switches, you can only create data VLANs with use of the vlan database command. In Cisco IOS Software Release 12.1(9)EA1 and later for the 2950 (and in all software versions for the 2940, 2955, and 2970), there is an additional option for the configuration of data VLANs. This additional option is the global vlan vlan-id command.

These examples use Fast Ethernet 0/1 as an access switch port and as a member of the management VLAN. No configuration is necessary in order to make an interface a member of VLAN 1 because all interfaces are access switch ports in VLAN 1 by default.

This is the first example:

Switch(config)#interface vlan 1

Switch(config-if)#ip address 10.1.1.1 255.0.0.0
Switch(config-if)#end
Switch#

Switch#show run interface vlan 1
Building configuration...
Current configuration:
!
interface VLAN1
ip address 10.1.1.1 255.0.0.0
no ip directed-broadcast
no ip route-cache
end

Switch#show run interface fastethernet 0/1
Building configuration...

Current configuration:
!
interface FastEthernet0/1

!--- All interfaces are access switch ports in VLAN 1 by default.

end

Switch#show ip interface brief
Interface IP-Address OK? Method Status Protocol
VLAN1 10.1.1.1 YES manual up up

FastEthernet0/1 unassigned YES unset up up

Remember that you cannot delete the VLAN 1 management interface. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI. You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

Note: The management interface can be in the shut down state after a reload if the management interface is not a member of VLAN 1 and if you have configured any of these commands on the switch:

  • ip ftp source-interface vlan vlan-id

  • ip tftp source-interface vlan vlan-id

  • ip telnet source-interface vlan vlan-id

    Make the management interface a member of VLAN 1. Alternatively, remove these commands from the configuration or upgrade the switch software to the latest image in order to solve this issue.

Note: On XL series switches, you can use the optional management command under the new SVI in order to automatically shut down VLAN 1 and transfer the IP address to the new VLAN.

Switch(config)#interface vlan 2

Switch(config-if)#ip address 20.1.1.1 255.0.0.0
Switch(config-if)#no shut

!--- Configure an interface to access the new management VLAN.

Switch(config)#interface fastethernet 0/1
Switch(config-if)#switchport access vlan 2
Switch(config-if)#end

Switch#

If you issue the show run interface fastethernet 0/1 command, this output now displays:

Switch#show run interface fastethernet 0/1

Building configuration...
Current configuration : 85 bytes
!
interface FastEthernet 0/1
switchport access vlan 2
switchport mode access
end
Switch#

In order for the switch to access remote networks, you must have a default gateway that is configured for the next hop router that is directly connected to the switch. Issue the ip default-gateway ip-address command in order to configure a gateway router IP address.

Configure a Management Interface for 3550 and 3750 Series Switches

On Catalyst 3550 and 3750 series switches that run Cisco IOS Software, any routable interface can be used for management. There are three options to configure this interface.

Option 1—Configure a loopback interface for switch management. There are a few advantages to a loopback interface. A loopback is a virtual interface that is always up. Packets that are routed to the loopback interface are rerouted back to the L3 switch or router and processed locally. IP packets that are routed out the loopback interface but are not destined to the loopback interface are dropped. This means that the loopback interface serves as the null 0 interface also. The loopback interface serves as the router ID for OSPF and so on. This example uses loopback 0:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface loopback 0
Switch(config-if)#ip address 10.1.1.1 255.255.255.255

!--- The loopback interface should have a 32-bit subnet mask, which means that
!--- the 10.1.1.1 address is the only destination address in this subnet.


Switch(config-if)#end
Switch#

You must also configure a routing protocol to distribute the subnet that is assigned to the loopback address or create a static route.

Option 2—Configure the interface as an L3 routed interface with an IP address. All interfaces on a Catalyst 3550 or 3750 switch that runs Cisco IOS Software are L2 by default. In order to make an L2 interface an L3 interface, issue the no switchport command and then configure an IP address. All interfaces are enabled by default, so you do not need to issue the no shutdown command. This example uses Fast Ethernet 2/0/1 on a Catalyst 3750:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface fastethernet 2/0/1
Switch(config-if)#no switchport
Switch(config-if)#ip address 11.1.1.1 255.0.0.0
Switch(config-if)#end
Switch#

If you issue the show running-config interface fastethernet 2/0/1 command, this output displays:

Switch#show running-config interface fastethernet 2/0/1

Building configuration...
Current configuration : 81 bytes
!
interface FastEthernet2/0/1
no switchport
ip address 11.1.1.1 255.0.0.0
end
Switch#

Option 3—Configure an L2 interface as a part of a specific VLAN. Issue the switchport mode access command and the switchport access vlan vlan-id command, and use a corresponding SVI with an IP address.

Complete these steps:

  1. Issue these commands:

    Switch(config)#interface vlan 1
    

    !--- Interface VLAN 1 is an SVI.

    Switch(config-if)#ip address 10.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    Note: This example uses VLAN 1 as the management VLAN. VLAN 1 is in the VLAN database by default.

  2. Issue the switchport mode access command under the desired physical interface if you want confirmation that the interface is an access switch port.

    By default, all interfaces are L2 interfaces and are access switch ports in VLAN 1. If you plan to use VLAN 1 as the management VLAN, no configuration is necessary under the interface. But if you want confirmation in the configuration that the interface is indeed an access switch port, you need to use the switchport mode access command.

    This example uses Fast Ethernet 2/0/1:

    Switch(config)#interface fastethernet 2/0/1
    
    Switch(config-if)#switchport mode access
    Switch(config-if)#end

    If you issue the show run interface fastethernet 2/0/1 command, this output now displays:

    Switch#show run interface fastethernet 2/0/1
    
    Building configuration...
    Current configuration : 59 bytes
    !
    interface FastEthernet2/0/1
    switchport mode access
    end
    Switch#
  3. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI.

    You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

    Switch(config)#interface vlan 2
    
    Switch(config-if)#ip address 20.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    !--- Configure an interface to access the new management VLAN.

    Switch(config)#interface fastethernet 2/0/1
    Switch(config-if)#switchport access vlan 2
    Switch(config-if)#end
    Switch#

    If you issue the show run interface fastethernet 2/0/1 command, this output now displays:

    Switch#show run interface fastethernet 2/0/1
    
    Building configuration...
    Current configuration : 85 bytes
    !
    interface FastEthernet2/0/1
    switchport access vlan 2
    switchport mode access
    end
    Switch#

    In order for the switch to access remote networks, you must have either:

    • A default gateway that is set for the next hop router that is directly connected to the switch

    • A dynamic routing protocol configured

    If you are not routing IP, issue the ip default-gateway ip-address command in order to configure a gateway router IP address.

    If you plan to configure dynamic routing, keep in mind that IP routing is disabled by default. You must issue the global ip routing command in order to enable IP routing. Routing Information Protocol (RIP) is the only dynamic routing protocol that is supported when you use the Standard Multilayer Software Image (SMI). The Enhanced Multilayer Software Image (EMI) is required for Interior Gateway Routing Protocol (IGRP), Enhanced IGRP (EIGRP), OSPF, and Border Gateway Protocol (BGP) support. In order to configure dynamic routing, use the router routing_protocol command. Issue the show ip route command in order to view the status of the routing table.