Saturday, January 15, 2011

Cisco 4500

This document describes how to configure a management IP address on Catalyst 4500/4000, 5500/5000, and 6500/6000 series switches that run Catalyst OS (CatOS) and Cisco IOS® Software. This document also includes Catalyst fixed configuration switches, which run Cisco IOS Software only and include the 2900/3500XL, 2940, 2950, 2955, 2970, 3550, and 3750 series switches. An IP address is necessary if you want to manage the switch from a remote TCP/IP capable management station. A switch that is to be managed by a VT100 terminal on its console port does not require an IP address.

Prerequisites

Requirements

Cisco recommends that you have knowledge of the information in this section.

Catalyst 4500/4000, 5500/5000, 6500/6000 switches that run only CatOS are Layer 2 (L2) switches. The Catalyst fixed configuration switches 2900/3500XLs, 2940, 2950, 2955, and 2970 are also L2 switches. The TCP/IP protocol on an L2 switch is for management purposes only. Data that flows through the switch can have Layer 3 (L3) addresses, such as IP, Internetwork Packet Exchange (IPX), AppleTalk, and so on. However, the switch uses only the data MAC address in order to determine from where traffic has come and which ports should receive the data. L2 switches ignore L3 addresses when the switches forward data.

The Catalyst 6500/6000, 4500/4000, and 3550/3750 series switches that run Cisco IOS Software are switch routers or L3 switches, and can use any interface for management. You can configure the management interface in any of these ways:

  • As a logical interface, like a loopback interface

  • As an L2 access port in a management VLAN

  • As an L3 interface with an IP address

    Note: This is the same way in which you configure the interface on any Cisco router.

The Catalyst switches that this document discusses have these management interfaces:

  • Catalyst 5500/5000 and 6500/6000 series switches with Supervisor Engines that run CatOS have two configurable IP management interfaces:

    • The in-band (sc0) interface

    • The Serial Line Internet Protocol (SLIP) (sl0) interface

  • Catalyst 4500/4000 switches with Supervisor Engines that run CatOS have three configurable IP management interfaces. The additional interface is called the management Ethernet (me1) interface.

  • Catalyst L2 fixed configuration switches that run Cisco IOS Software have only one configurable IP management interface, which by default is interface VLAN 1.

  • Pure layer 2 switches can have only one interface VLAN up at the time. This is called the management VLAN (in IOS) or the sc0 interface (in CatOS). The main purpose of this interface is management (telnet, SNMP, etc). If the switch is a Layer 3 switch, you can configure multiple VLANs and route between them. An L3 switch can handle multiple IPs, so there is no specific management VLAN on the switch.

  • Catalyst 3550/3750 series switches that run Cisco IOS Software can use any interface for management.

Components Used

This document is not restricted to specific software and hardware versions.

The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.

Conventions

Refer to Cisco Technical Tips Conventions for more information on document conventions.

Catalyst 4500/4000, 5500/5000, and 6500/6000 Management Interfaces

The sc0 interface is an internal management interface connected to the switching fabric. The sc0 interface participates in all the functions of a normal switch port, which include:

  • Spanning Tree Protocol (STP)

  • Cisco Discovery Protocol (CDP)

  • Virtual LAN (VLAN) membership

The me1 and sl0 interfaces are out-of-band management interfaces that are not connected to the switching fabric and do not participate in any of these functions.

When you configure the IP address, subnet mask, and broadcast address (and, on the sc0 interface, VLAN membership) of the sc0 or me1 interface, you can access the switch through Telnet or Simple Network Management Protocol (SNMP). When you configure the SLIP (sl0) interface, you can open a point-to-point connection to the switch through the console port from a workstation.

If you have the output of a show interface command from your Cisco device, you can use the Output Interpreter (registered customers only) tool to display potential issues and fixes.

The sc0 does not have an external port for direct connection. This interface exists as a logical interface inside the switch and is accessible through any of the physical ports on the switch. This figure provides an illustration:

8a.gif

The me1 is actually a physical Ethernet port on the Supervisor Engine module on the Catalyst 4500/4000 series switches. This interface is used for network management only and does not support network switching.

8d.gif

The sl0 uses the RS232 console port as its physical interface. The sl0 cannot be used as a VT100 console when it is in SLIP mode. This figure illustrates a SLIP connection to sl0:

8b.gif

Configure the sc0 Interface on Catalyst 4500/4000, 5500/5000, and 6500/6000 Switches That Run CatOS

This section describes how to configure an IP address on the in-band sc0 interface.

  1. Connect a terminal to the console ports of the switches.

    For details on how to connect to the console ports of the Catalyst switches, refer to Connecting a Terminal to the Console Port on Catalyst Switches.

  2. Issue the show interface command at the switch prompt in order to view the default status of the management interfaces.

    Switch-A> (enable) show interface
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    !--- Catalyst 5500/5000 and 6500/6000 series switches
    !--- do not display the me1 interface in the output.


    Switch-A> (enable)
  3. Issue the set interface sc0 172.16.84.17 255.255.255.0 172.16.84.255 command in order to configure an IP address for sc0.

    The message that the switch returns tells you which parameters have been changed.

    Note: When you issue the set interface sc0 command, you cannot enter the broadcast address without the subnet mask of the IP address.

    Switch-A> (enable) set interface sc0 172.16.84.17 255.255.255.0 172.16.84.255 
    
    Interface sc0 IP address, netmask, and broadcast set.
    Switch-A> (enable)

    Issue the show interface command in order to view the changes.

    Switch-A> (enable) show interface 
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 172.16.84.17 netmask 255.255.255.0 broadcast 172.16.84.255
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    Switch-A> (enable)

    If you enter only an IP address after the set interface sc0 172.16.84.17 command, the default mask and the default broadcast address for the address class are automatically configured. Here is an example:

    Switch-A> (enable) set interface sc0 172.16.84.17
    

    !--- Notice that neither the mask nor the broadcast address is specified.

    Interface sc0 IP address and netmask set.
    Switch-A> (enable)
    Switch-A> (enable) show interface
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 172.16.84.17 netmask 255.255.0.0 broadcast 172.16.255.255

    !--- Notice that the switch took the default mask
    !--- and the broadcast address of class B.


    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    Switch-A> (enable)

    If you enter the IP address and subnet mask after the set interface sc0 command, the broadcast address for the specific subnet is automatically configured.

  4. In order to change the VLAN on the sc0 interface, issue the set interface sc0 vlan# command, which specifies the VLAN number.

    Note: By default, the sc0 interface belongs to VLAN 1.

    If you want to change the membership of sc0 to VLAN 2, issue this command:

    Switch-A> (enable) set interface sc0 2 
    


    Interface sc0 vlan set.
    Switch-A> (enable)

    Note: Be sure that you have configured VLAN 2 on the switch before you issue this command. The configuration of VLANs on Catalyst switches is beyond the scope of this document. For more information, refer to Creating Ethernet VLANs on Catalyst Switches.

    Issue the show interface command in order to view the changes.

    Switch-A> (enable) show interface
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 2 inet 172.16.84.17 netmask 255.255.255.0 broadcast 172.16.84.255
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    Switch-A> (enable)
  5. Issue the show ip route command.

    Note: If you want to be able to manage the switch through a router, you must configure a default gateway. The switch does not participate in IP routing. Therefore, the switch has no knowledge of the L3 topology of the network.

    When you issue the show ip route command, notice that the gateway for the subnet sc0 is assigned to its own address.

    Switch-A> (enable) show ip route 
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    172.16.84.0 172.16.84.17 0xffffff00 U 395 sc0
    default default 0xff000000 UH 0 sl0
    Switch-A> (enable)
  6. Issue the set ip route 0.0.0.0 172.16.84.1 command or the set ip route default 172.16.84.1 command in order to establish the default route.

    The second IP address is the directly connected router that will be your path through the rest of the network. This IP address must be part of the same IP subnet as the switch. You can define up to three default IP gateways. Use the primary keyword with the set ip route command in order to make a gateway the primary gateway. If you do not specify a primary default gateway, the first gateway that is configured is the primary gateway. If more than one gateway is designated as primary, the last primary gateway that is configured is the primary default gateway.

    • Switch-A> (enable) set ip route 0.0.0.0 172.16.84.1 
      
      Route added.
      Switch-A> (enable)

    or

    • Switch-A> (enable) set ip route default 172.16.84.1
      
      Route added.
      Switch-A> (enable)

    Issue the show ip route command in order to view the changes.

    Switch-A> (enable) show ip route 
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 172.16.84.1
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 172.16.84.1 0x0 UG 0 sc0
    172.16.84.0 172.16.84.17 0xffffff00 U 525 sc0
    default default 0xff000000 UH 0 sl0
    Switch-A> (enable)
  7. If you need to clear the routes from the routing table, issue the clear ip route all command.

    Note: If you are connected to the switch through Telnet from a different subnet, you lose connection when you clear the routes. You cannot reach the switch again until someone reenters the gateway address through an attached console or a PC/terminal that is on the same subnet as the switch.

    Switch-A> (enable) clear ip route all
    
    All routes deleted.
    Switch-A> (enable)

    You can clear a single route if you specify only that route. Issue the clear ip route 0.0.0.0 172.16.84.1 command.

Configure the SLIP (sl0) Interface on Catalyst 4500/4000, 5500/5000, and 6500/6000 Switches That Run CatOS

You can use a SLIP connection over sl0 in order to monitor or manage the switch remotely with a TCP/IP-capable device where there is no other path to the switch except through the console port.

A network manager can use a remote PC to dial up switches anywhere in the world and manage the switches with the use of SNMP or Telnet over SLIP. You can also upload system software over the sl0 interface with the use of TFTP. Without SLIP, the console port can only be used for VT100 access (tty) or Kermit file transfers. Refer to Connecting a Modem to the Console Port on Catalyst Switches for more information on how to enable dialup connectivity to a Catalyst switch.

This figure shows an example of the management of a switch by a remote terminal with the use of sl0. This type of management is sometimes referred to as out-of-band management. Out-of-band means that a management terminal accesses the device through a path that does not include the network to which the switch is connected.

8c.gif

If you set up and activate the sl0 interface from a directly attached console terminal, you lose your console connection. If the terminal that you use supports SLIP, establish a SLIP session with the switch. Deactivate the SLIP connection when you finish in order to allow direct console connectivity. If you activate SLIP and your terminal does not support SLIP, you must establish a Telnet connection to the switch and deactivate sl0 or power cycle the switch in order to regain access to the console port.

Note: Unless you have a terminal that can run SLIP and you know how to use it, only perform these steps from a Telnet connection to the switch.

  1. Establish a Telnet session to the switch.

  2. Issue the set interface sl0 1.1.1.1 1.1.1.2 command at the command prompt in order to set the SLIP address of the switch and the destination IP address.

    Here is an example:

    Switch-A> (enable) set interface sl0 1.1.1.1 1.1.1.2
    
    Interface sl0 slip and destination address set.
    Switch-A> (enable)
  3. Issue the slip attach command at the command prompt in order to activate SLIP mode.

    Here is an example:

    Switch-A> (enable) slip attach
    
    Console Port now running SLIP.
    Switch-A> (enable)
  4. Issue the slip detach command at the command prompt in order to deactivate SLIP mode.

    Here is an example:

    Switch-A> (enable) slip detach
    
    SLIP detached on Console port.
    Switch-A> (enable)

Configure the Management Ethernet Interface (me1) on a Catalyst 4500/4000 That Runs CatOS

This section explains how to configure an IP address on the me1 that is present on the Catalyst 4500/4000 series switches. Packets received on the me1 interface never reach the switching fabric, and there is no access to the me1 interface except through the Ethernet port on the Supervisor Engine.

Another characteristic of the me1 interface is that, when the switch is in ROM monitor (ROMmon), interface me1 is the only interface that is active. You can boot from the network through me1 or upgrade the Cisco IOS Software through me1 while in ROMmon. However, you must be directly on the console port. You can use this interface when you recover a Catalyst 4500/4000 series switch from a corrupted or missing software image or from an upgrade failure. For those details, refer to the Recovering the Catalyst 4000, Catalyst 2948G, Catalyst 2980G, and Catalyst 4912G section of Recovering Catalyst Switches Running CatOS from Booting Failures.

You configure the IP address on the me1 interface in a way that is similar to the configuration on the sc0 interface. The only difference is that you cannot attach the me1 interface to any VLAN because this interface does not reach the switching fabric as the sc0 interface does.

Complete these steps in order to configure an IP address on the me1 interface:

  1. Connect a terminal to the console port of the switch.

  2. Issue the show interface command at the switch prompt in order to view the default status of the me1 interface.

    Here is an example:

    Switch-A> (enable) show interface
    
    sl0: flags=51
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    me1: flags=62
    inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    Switch-A> (enable)
  3. Issue the set interface me1 10.1.1.2 255.255.255.0 10.1.1.255 command in order to configure an IP address for me1.

    The message that the switch returns tells you which parameters have been changed.

    Note: You must enter a netmask in order to configure a broadcast address.

    Switch-A> (enable) set interface me1 10.1.1.2 255.255.255.0 10.1.1.255
    
    Interface me1 IP address, netmask, and broadcast set.
    Switch-A> (enable)

    Issue the show interface command in order to view the changes that you have made.

    Switch-A> (enable) show interface
    
    sl0: flags=50
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0
    me1: flags=63
    inet 10.1.1.2 netmask 255.255.255.0 broadcast 10.1.1.255

    Switch-A> (enable)

    If you enter only an IP address after the set interface me1 10.1.1.2 command, the default mask and the default broadcast address for the address class that you used are configured. Here is an example:

    Switch-A> (enable) set interface me1 10.1.1.2
    

    !--- Notice that neither the mask nor the broadcast address is specified.

    Interface sc0 IP address and netmask set.
    Switch-A> (enable)

    Switch-A> (enable) show interface
    sl0: flags=50
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=63
    vlan 1 inet 0.0.0.0 netmask 0.0.0.0 broadcast 0.0.0.0

    me1: flags=63 <UP,BROADCAST,RUNNING>
    inet 10.1.1.2 netmask 255.0.0.0 broadcast 10.255.255.255

    !--- Notice that the switch took the
    !--- default mask and the broadcast address of class A.


    Switch-A> (enable)

    Note: Normally, the me1 interface is configured to be in a different subnet than the sc0 interface, which allows both interfaces to remain up. Both interfaces can be configured in the same subnet or with the same IP address, but the sc0 interface is shut down in this case. Interface me1 always takes precedence in this instance. For example, if you have already configured the sc0 interface with an IP address of 172.16.84.17 255.255.255.0, and you try to configure the me1 interface in the same subnet (172.16.84.18 255.255.255.0), you see these messages:

    Switch-A> (enable) set interface me1 172.16.84.18 255.255.255.0 172.16.80.255
    
    This command places me1 and sc0 into the same ip subnet.
    The sc0 interface will be automatically configured down if necessary to resolve
    the conflict.
    Do you want to continue (y/n) [n]?y
    Interface me1 IP address, netmask, and broadcast set.
    Interface sc0 administratively down due to conflict.
    Console> (enable)

    !--- Check the configuration.

    Switch-A> (enable) show interface
    sl0: flags=50
    slip 0.0.0.0 dest 0.0.0.0
    sc0: flags=62 <DOWN,BROADCAST,RUNNING>
    vlan 1 inet 172.16.84.17 netmask 255.255.255.0 broadcast 172.16.84.255
    me1: flags=63
    inet 172.16.84.18 netmask 255.255.255.0 broadcast 172.16.84.255
    Switch-A> (enable)
  4. If you noticed in Step 3 that the status of me1 is down instead of up, issue this command in order to bring the interface up manually:

    Switch-A> (enable) set interface me1 up
    
    Interface me1 administratively up.
    Switch-A> (enable)
  5. Issue the show ip route command.

    Note: If you want to be able to manage the switch through a router, you must configure a default gateway because the switch does not participate in IP routing. Therefore, the switch has no knowledge of the L3 topology of the network.

    When you issue the show ip route command, notice that the gateway for the subnet me1 is assigned to its own address.

    Switch-A> (enable) show ip route 
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    10.1.1.0 10.1.1.2 0xffffff00 U 0 me1
    Switch-A> (enable)
  6. Issue the set ip route 0.0.0.0 10.1.1.3 command or the set ip route default 10.1.1.3 command in order to establish the default route.

    The second IP address is the directly connected router that will be your path through the rest of the network. This IP address must be part of the same IP subnet as the switch.

    • Switch-A> (enable)set ip route 0.0.0.0 10.1.1.3
      
      Route added.
      Switch-A> (enable)

    or

    • Switch-A> (enable) set ip route default 10.1.1.3
      
      Route added.
      Switch-A> (enable)

    Issue the show ip route command in order to view the changes.

    Switch-A> (enable) show ip route
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 10.1.1.3
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 10.1.1.3 0x0 UG 0 me1
    10.1.1.0 10.1.1.2 0xffffff00 U 1 me1
    Switch-A> (enable)

    Note: If sc0 and me1 are in different subnets, you can configure multiple default gateways. However, the gateway that is defined first becomes the primary gateway. If this is the gateway that you intend, you must use the keyword primary at the end of the command in order to change the primary default gateway. For example, 172.16.84.1 is the primary gateway in a case in which both these item are true:

    • You have sc0 with IP address 172.16.84.17 255.255.255.0 configured first with the default gateway of 172.16.84.1.

    • You configure me1 with an IP address of 10.1.1.2 255.255.255.0 and with the default gateway of 10.1.1.3.

    You can issue these commands in order to change the primary gateway to 10.1.1.3:

    Switch-A> (enable) show ip route
    
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 172.16.80.1
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 10.1.1.3 0x0 G 0 me1
    default 172.16.84.1 0x0 UG 11 sc0
    172.16.80.0 172.16.84.17 0xffffff00 U 38 sc0
    10.1.1.0 10.1.1.2 0xffffff00 U 4 me1

    !--- Notice that 172.16.84.1 is the primary default gateway.

    Switch-A> (enable)

    !--- Change the primary default gateway to 10.1.1.3.

    Switch-A> (enable) set ip route default 10.1.1.3 primary
    Primary route changed
    Switch-A> (enable)

    !--- This message displays when the primary gateway is changed:

    %SYS-5-RTE_DEFGATEFROM:Default Gateway switching from 172.16.80.1
    %SYS-5-RTE_DEFGATETO:Default Gateway switching to 10.1.1.3

    !--- Verify the change.

    Switch-A> (enable) show ip route
    Fragmentation Redirect Unreachable
    ------------- -------- -----------
    enabled enabled enabled

    The primary gateway: 10.1.1.3
    Destination Gateway RouteMask Flags Use Interface
    --------------- --------------- ---------- ----- -------- ---------
    default 10.1.1.3 0x0 UG 0 me1
    default 172.16.84.1 0x0 G 11 sc0
    172.16.80.0 172.16.84.17 0xffffff00 U 38 sc0
    10.1.1.0 10.1.1.2 0xffffff00 U 4 me1

    !--- Notice that now the primary default gateway is 10.1.1.3.

  7. If you need to clear the routes from the routing table, issue the clear ip route all command.

    Note: If you are connected to the switch through Telnet from a different subnet, your connection is lost when you clear the routes. You cannot reach the switch again until someone reenters the gateway address via an attached console or a PC/terminal on the same subnet as the switch.

    Switch-A> (enable) clear ip route all
    
    All routes deleted.
    Switch-A> (enable)

    You can clear a single route if you specify only that route. Issue the clear ip route 0.0.0.0 10.1.1.3 command.

Configure a Management Interface for Catalyst 4500/4000 Series Switches That Run Cisco IOS Software

On a Catalyst 4500/4000 Supervisor Engine III/IV that runs Cisco IOS Software, any routable interface can be used for management. There are three options to configure this interface.

Note: The Ethernet management port (labeled 10/100 MGT) on a Supervisor Engine III (WS-X4014) or Supervisor Engine IV (WS-X4515) is used in ROMmon mode only to recover a switch software image that is missing or corrupted. This port is not active during normal switch operation and cannot be used as a management interface.

Option 1—Configure a loopback interface for switch management. There are a few advantages to a loopback interface. A loopback is a virtual interface that is always up. Packets that are routed to the loopback interface are rerouted back to the L3 switch or router and processed locally. IP packets that are routed out the loopback interface but are not destined to the loopback interface are dropped. This means that the loopback interface serves as the null 0 interface also. The loopback interface serves as the router ID for Open Shortest Path First (OSPF) and so on. This example uses loopback 0:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface loopback 0
Switch(config-if)#ip address 10.1.1.1 255.255.255.255

!--- The loopback interface should have a 32-bit subnet mask, which means that
!--- the 10.1.1.1 address is the only destination address in this subnet.


Switch(config-if)#end
Switch#

You must also configure a routing protocol to distribute the subnet that is assigned to the loopback address or create a static route.

Option 2—Configure the interface as an L3 routed interface with an IP address. All interfaces on a Catalyst 4500/4000 switch that runs Cisco IOS Software are L2 by default. Therefore, you need to make any interface that is connected to the rest of the network an L3 routed interface. Issue the no switchport command, and configure the desired IP address. The example provides an illustration. All interfaces are enabled by default, so you do not need to issue the no shutdown command. This example uses Fast Ethernet 5/30:

Switch(config)#interface fastethernet 5/30

Switch(config-if)#no switchport
Switch(config-if)#ip address 11.1.1.1 255.0.0.0

If you issue the show running-config interface fastethernet 5/30 command, this output displays:

Building configuration...

Current configuration : 80 bytes
!
interface FastEthernet5/30
no switchport
ip address 11.1.1.1 255.0.0.0
end

Option 3—Configure an L2 interface as a part of a specific VLAN. Issue the switchport mode access command and the switchport access vlan vlan-id command, and use a corresponding switched virtual interface (SVI) with an IP address.

Note: You must understand the difference between the management VLAN that is used to administer the switch and data VLANs that are used to pass L2 traffic. The management VLAN is an SVI the you create with use of the global interface vlan vlan-id command. Do not confuse this command with the commands that you use to create data VLANs to pass L2 traffic. On Catalyst 6500/6000 series switches that run Cisco IOS Software, you can configure data VLANs from the VLAN database or you can issue the global vlan vlan-id command.

Complete these steps:

  1. Issue these commands:

    Switch(config)#interface vlan 1
    
    Switch(config-if)#ip address 10.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    Note: This example uses VLAN 1 as the management VLAN. VLAN 1 is in the VLAN database by default.

  2. Issue the switchport mode access command under the desired physical interface if you want confirmation that the interface is an access switch port.

    By default, all interfaces are L2 interfaces and are access switch ports in VLAN 1. If you plan to use VLAN 1 as the management VLAN, no configuration is necessary under the interface. But if you want confirmation in the configuration that the interface is indeed an access switch port, you need to use the switchport mode access command.

    This example uses Fast Ethernet 5/32:

    Switch(config)#interface fastethernet 5/32
    
    Switch(config-if)#switchport mode access

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Switch#show run interface fastethernet 5/32
    
    Building configuration...

    Current configuration : 84 bytes
    !
    interface FastEthernet5/32
    switchport mode access
    no snmp trap link-status
    end
  3. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI.

    You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

    Switch(config)#interface vlan 2
    
    Switch(config-if)#ip address 20.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    !--- Configure an interface to access the new management VLAN.

    Switch(config)#interface fastethernet 5/32
    Switch(config-if)#switchport mode access
    Switch(config-if)#switch access vlan 2

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Building configuration...
    
    Current configuration : 110 bytes
    !
    interface FastEthernet5/32
    switchport access vlan 2
    switchport mode access
    end

    In order for the switch to access remote networks, you must have either:

    • A default gateway that is set for the next hop router that is directly connected to the switch

    • A dynamic routing protocol configured

    If you are not routing IP, issue the ip default-gateway ip-address command in order to configure a gateway router IP address. In order to configure dynamic routing, use the router routing_protocol command. Issue the show ip route command in order to view the status of the routing table.

Configure a Management Interface for a Catalyst 6500/6000 Switch That Runs Cisco IOS Software

On a Catalyst 6500/6000 series switch that runs Cisco IOS Software, any routable interface can be used for management. There are three options to configure this interface.

Option 1—Configure a loopback interface for switch management. There are a few advantages to a loopback interface. A loopback is a virtual interface that is always up. Packets that are routed to the loopback interface are rerouted back to the L3 switch or router and processed locally. IP packets that are routed out the loopback interface but are not destined to the loopback interface are dropped. This means that the loopback interface serves as the null 0 interface also. The loopback interface serves as the router ID for OSPF and so on. This example uses loopback 0:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface loopback 0
Switch(config-if)#ip address 10.1.1.1 255.255.255.255

!--- The loopback interface should have a 32-bit subnet mask, which means that
!--- the 10.1.1.1 address is the only destination address in this subnet.


Switch(config-if)#end
Switch#

You must also configure a routing protocol to distribute the subnet that is assigned to the loopback address or create a static route.

Option 2—Configure the interface as an L3 routed interface with an IP address. All interfaces on a Catalyst 6500/6000 switch that runs Cisco IOS Software are L3 by default. All interfaces are enabled by default, so you do not need to issue the no shutdown command. This example uses Fast Ethernet 5/30:

Switch(config)#interface fastethernet 5/30

Switch(config-if)#ip address 11.1.1.1 255.0.0.0

If you issue the show running-config interface fastethernet 5/30 command, this output displays:

Building configuration...

Current configuration : 80 bytes
!
interface FastEthernet5/30
no switchport
ip address 11.1.1.1 255.0.0.0
end

Option 3—Configure an L2 interface as a part of a specific VLAN. Issue the switchport mode access command and the switchport access vlan vlan-id command, and use a corresponding SVI with an IP address.

Note: You must understand the difference between the management VLAN that is used to administer the switch and data VLANs that are used to pass L2 traffic. The management VLAN is an SVI that you create with use of the global interface vlan vlan-id command. Do not confuse this command with the commands that you use to create data VLANs to pass L2 traffic. On Catalyst 6500/6000 series switches that run Cisco IOS Software, you can configure data VLANs from the VLAN database or you can issue the global vlan vlan-id command.

Complete these steps:

  1. Issue these commands:

    Switch(config)#interface vlan 1
    

    !--- Interface VLAN 1 is an SVI.

    Switch(config-if)#ip address 10.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    Note: This example uses VLAN 1 as the management VLAN. VLAN 1 is in the VLAN database by default.

  2. Issue the switchport mode access command under the desired physical interface in order to make the interface an L2 interface in default VLAN 1.

    Note: By default, all interfaces are L3 interfaces.

    This example uses Fast Ethernet 5/32:

    Switch(config)#interface fastethernet 5/32
    
    Switch(config-if)#switchport mode access

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Switch#show run interface fastethernet 5/32
    
    Building configuration...
    Current configuration : 84 bytes
    !
    interface FastEthernet5/32
    switchport mode access
    no snmp trap link-status
    end
  3. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI.

    You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

    Switch(config)#interface vlan 2
    
    Switch(config-if)#ip address 20.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    !--- Configure an interface to access the new management VLAN.

    Switch(config)#interface fastethernet 5/32
    Switch(config-if)#switchport mode access
    Switch(config-if)#switch access vlan 2

    If you issue the show run interface fastethernet 5/32 command, this output now displays:

    Building configuration...
    
    Current configuration : 110 bytes
    !
    interface FastEthernet5/32
    switchport access vlan 2
    switchport mode access
    end

    In order for the switch to access remote networks, you must have either:

    • A default gateway that is set for the next hop router that is directly connected to the switch

    • A dynamic routing protocol configured

    If you are not routing IP, issue the ip default-gateway ip-address command in order to configure a gateway router IP address. In order to configure dynamic routing, use the router routing_protocol command. Issue the show ip route command in order to view the status of the routing table.

Configure a Management Interface for Catalyst L2 Fixed Configuration Switches

The Catalyst L2 fixed configuration switches run Cisco IOS Software, but are L2-capable switches only. These switches can have only one active management interface at a time. The default management interface is VLAN 1. You cannot delete VLAN 1 on these switches. However, you can create another VLAN interface for management, which the examples in this section demonstrate.

Note: You must understand the difference between the management VLAN that is used to administer the switch and VLANs that are used to pass L2 traffic. The management VLAN is an SVI that you create with use of the global interface vlan vlan-id command. Do not confuse this command with the commands that you use to create data VLANs to pass L2 traffic. On XL series switches, you can only create data VLANs with use of the vlan database command. In Cisco IOS Software Release 12.1(9)EA1 and later for the 2950 (and in all software versions for the 2940, 2955, and 2970), there is an additional option for the configuration of data VLANs. This additional option is the global vlan vlan-id command.

These examples use Fast Ethernet 0/1 as an access switch port and as a member of the management VLAN. No configuration is necessary in order to make an interface a member of VLAN 1 because all interfaces are access switch ports in VLAN 1 by default.

This is the first example:

Switch(config)#interface vlan 1

Switch(config-if)#ip address 10.1.1.1 255.0.0.0
Switch(config-if)#end
Switch#

Switch#show run interface vlan 1
Building configuration...
Current configuration:
!
interface VLAN1
ip address 10.1.1.1 255.0.0.0
no ip directed-broadcast
no ip route-cache
end

Switch#show run interface fastethernet 0/1
Building configuration...

Current configuration:
!
interface FastEthernet0/1

!--- All interfaces are access switch ports in VLAN 1 by default.

end

Switch#show ip interface brief
Interface IP-Address OK? Method Status Protocol
VLAN1 10.1.1.1 YES manual up up

FastEthernet0/1 unassigned YES unset up up

Remember that you cannot delete the VLAN 1 management interface. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI. You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

Note: The management interface can be in the shut down state after a reload if the management interface is not a member of VLAN 1 and if you have configured any of these commands on the switch:

  • ip ftp source-interface vlan vlan-id

  • ip tftp source-interface vlan vlan-id

  • ip telnet source-interface vlan vlan-id

    Make the management interface a member of VLAN 1. Alternatively, remove these commands from the configuration or upgrade the switch software to the latest image in order to solve this issue.

Note: On XL series switches, you can use the optional management command under the new SVI in order to automatically shut down VLAN 1 and transfer the IP address to the new VLAN.

Switch(config)#interface vlan 2

Switch(config-if)#ip address 20.1.1.1 255.0.0.0
Switch(config-if)#no shut

!--- Configure an interface to access the new management VLAN.

Switch(config)#interface fastethernet 0/1
Switch(config-if)#switchport access vlan 2
Switch(config-if)#end

Switch#

If you issue the show run interface fastethernet 0/1 command, this output now displays:

Switch#show run interface fastethernet 0/1

Building configuration...
Current configuration : 85 bytes
!
interface FastEthernet 0/1
switchport access vlan 2
switchport mode access
end
Switch#

In order for the switch to access remote networks, you must have a default gateway that is configured for the next hop router that is directly connected to the switch. Issue the ip default-gateway ip-address command in order to configure a gateway router IP address.

Configure a Management Interface for 3550 and 3750 Series Switches

On Catalyst 3550 and 3750 series switches that run Cisco IOS Software, any routable interface can be used for management. There are three options to configure this interface.

Option 1—Configure a loopback interface for switch management. There are a few advantages to a loopback interface. A loopback is a virtual interface that is always up. Packets that are routed to the loopback interface are rerouted back to the L3 switch or router and processed locally. IP packets that are routed out the loopback interface but are not destined to the loopback interface are dropped. This means that the loopback interface serves as the null 0 interface also. The loopback interface serves as the router ID for OSPF and so on. This example uses loopback 0:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface loopback 0
Switch(config-if)#ip address 10.1.1.1 255.255.255.255

!--- The loopback interface should have a 32-bit subnet mask, which means that
!--- the 10.1.1.1 address is the only destination address in this subnet.


Switch(config-if)#end
Switch#

You must also configure a routing protocol to distribute the subnet that is assigned to the loopback address or create a static route.

Option 2—Configure the interface as an L3 routed interface with an IP address. All interfaces on a Catalyst 3550 or 3750 switch that runs Cisco IOS Software are L2 by default. In order to make an L2 interface an L3 interface, issue the no switchport command and then configure an IP address. All interfaces are enabled by default, so you do not need to issue the no shutdown command. This example uses Fast Ethernet 2/0/1 on a Catalyst 3750:

Switch#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface fastethernet 2/0/1
Switch(config-if)#no switchport
Switch(config-if)#ip address 11.1.1.1 255.0.0.0
Switch(config-if)#end
Switch#

If you issue the show running-config interface fastethernet 2/0/1 command, this output displays:

Switch#show running-config interface fastethernet 2/0/1

Building configuration...
Current configuration : 81 bytes
!
interface FastEthernet2/0/1
no switchport
ip address 11.1.1.1 255.0.0.0
end
Switch#

Option 3—Configure an L2 interface as a part of a specific VLAN. Issue the switchport mode access command and the switchport access vlan vlan-id command, and use a corresponding SVI with an IP address.

Complete these steps:

  1. Issue these commands:

    Switch(config)#interface vlan 1
    

    !--- Interface VLAN 1 is an SVI.

    Switch(config-if)#ip address 10.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    Note: This example uses VLAN 1 as the management VLAN. VLAN 1 is in the VLAN database by default.

  2. Issue the switchport mode access command under the desired physical interface if you want confirmation that the interface is an access switch port.

    By default, all interfaces are L2 interfaces and are access switch ports in VLAN 1. If you plan to use VLAN 1 as the management VLAN, no configuration is necessary under the interface. But if you want confirmation in the configuration that the interface is indeed an access switch port, you need to use the switchport mode access command.

    This example uses Fast Ethernet 2/0/1:

    Switch(config)#interface fastethernet 2/0/1
    
    Switch(config-if)#switchport mode access
    Switch(config-if)#end

    If you issue the show run interface fastethernet 2/0/1 command, this output now displays:

    Switch#show run interface fastethernet 2/0/1
    
    Building configuration...
    Current configuration : 59 bytes
    !
    interface FastEthernet2/0/1
    switchport mode access
    end
    Switch#
  3. If you want to change the management interface from the default VLAN 1 to another VLAN, issue the interface vlan vlan-id command in order to create a new SVI.

    You must then issue the switchport access vlan vlan-id command in order to configure an L2 interface to be a part of the new VLAN. This example demonstrates this process:

    Switch(config)#interface vlan 2
    
    Switch(config-if)#ip address 20.1.1.1 255.0.0.0
    Switch(config-if)#no shut

    !--- Configure an interface to access the new management VLAN.

    Switch(config)#interface fastethernet 2/0/1
    Switch(config-if)#switchport access vlan 2
    Switch(config-if)#end
    Switch#

    If you issue the show run interface fastethernet 2/0/1 command, this output now displays:

    Switch#show run interface fastethernet 2/0/1
    
    Building configuration...
    Current configuration : 85 bytes
    !
    interface FastEthernet2/0/1
    switchport access vlan 2
    switchport mode access
    end
    Switch#

    In order for the switch to access remote networks, you must have either:

    • A default gateway that is set for the next hop router that is directly connected to the switch

    • A dynamic routing protocol configured

    If you are not routing IP, issue the ip default-gateway ip-address command in order to configure a gateway router IP address.

    If you plan to configure dynamic routing, keep in mind that IP routing is disabled by default. You must issue the global ip routing command in order to enable IP routing. Routing Information Protocol (RIP) is the only dynamic routing protocol that is supported when you use the Standard Multilayer Software Image (SMI). The Enhanced Multilayer Software Image (EMI) is required for Interior Gateway Routing Protocol (IGRP), Enhanced IGRP (EIGRP), OSPF, and Border Gateway Protocol (BGP) support. In order to configure dynamic routing, use the router routing_protocol command. Issue the show ip route command in order to view the status of the routing table.

Monday, December 6, 2010

ccna security exam new dumps 2010

CBT Nuggets: Cisco CCNA Security - Exam-Pack 640-553: IINS

CBT Nuggets: Cisco CCNA Security - Exam-Pack 640-553: IINS
CBT Nuggets: Cisco CCNA Security - Exam-Pack 640-553: IINS | 1.6GB
English

Are you an IT Pro responsible for network security? Do you have CCNA certification and want to take the next step in network security? Are you working towards CCSP certification? If any of these are you, this is the training you’re looking for.
Jump into security with Jeremy Cioara’s Cisco CCNA Security video series. Jeremy puts you in the mind of hackers and intruders and shows you how to defeat these black hats. Soon you’ll be recognizing different types of attackers and threats and eliminating the damage that can follows security breaches.

CBT Nuggets: Cisco CCNA Security - Exam-Pack 640-553: IINS

CBT Nuggets: Cisco CCNA Security - Exam-Pack 640-553: IINS
CBT Nuggets: Cisco CCNA Security - Exam-Pack 640-553: IINS | 1.6GB
English

Are you an IT Pro responsible for network security? Do you have CCNA certification and want to take the next step in network security? Are you working towards CCSP certification? If any of these are you, this is the training you’re looking for.
Jump into security with Jeremy Cioara’s Cisco CCNA Security video series. Jeremy puts you in the mind of hackers and intruders and shows you how to defeat these black hats. Soon you’ll be recognizing different types of attackers and threats and eliminating the damage that can follows security breaches.

CBT Nuggets Cisco CCNA Security - Exam-Pack 640-553: IINS


CBT Nuggets Cisco CCNA Security - Exam-Pack 640-553: IINS
CBT Nuggets Cisco CCNA Security - Exam-Pack 640-553: IINS | 1680MB



CBT Nuggets Cisco CCNA Security Exam-Pack 640-553 IINS

CBT Nuggets Cisco CCNA Security Exam-Pack 640-553 IINS
CBT Nuggets: Cisco CCNA Security – Exam Pack 640 553: IINS | 1.6GB

Are you an IT Pro responsible for network security? Do you have CCNA certification and want to take the next step in network security? Are you working towards CCSP certification? If any of these are you, this is the training you’re looking for.
Jump into security with Jeremy Cioara’s Cisco CCNA Security video series. Jeremy puts you in the mind of hackers and intruders and shows you how to defeat these black hats. Soon you’ll be recognizing different types of attackers and threats and eliminating the damage that can follows security breaches.

CCNA Security Exam Cram (Exam IINS 640-553)

CCNA Security Exam Cram (Exam IINS 640-553)


CCNA Security Exam Cram (Exam IINS 640-553)
ISBN 978-0789738004 | 559 Pages | Release Date 03/03/2009 | PDF | 12.4 MB

TrainSignal - Cisco CCNA Security Training and Cisco IINS 640-553 Exam

TrainSignal - Cisco CCNA Security Training and Cisco IINS 640-553 Exam
TrainSignal - Cisco CCNA Security Training and Cisco IINS 640-553 Exam
DVD ISO | 2.2GB + 2GB

In as little as 13 hours, you'll learn how to identify, lockdown, & secure vulnerabilities in a small to medium enterprise branch Nntwork... and have the knowledge necessary to pass the Cisco CCNA Security/IINS 640-553 Exam...Guaranteed!

Cisco 2010 ccna 640-802 dumps 250 questions

1. How to go about preparing for the CCNA test from scratch.?
2. Are Linux courses like RHCE (Redhat Certified Engineer) course, CCNA courses…
3. Is ccna and mcse are similar course?
4. should i take the CCNA program?
5. I Have A Ccna Cbt & Running Vista On A New Laptop I’m Able 2 Load Main Pg Ccna1-4 Bt
6. Where i can get Cisco ccna Exams answers ?
7. which is better ccna or mcitp?
8. can i get job only ccna or any cisco certificate after a finish i do not
9. what are ccna nuggets files?
10. what great deal does CCNA have to offer?
11. CCNA examination information?
12. CCNA examination information?
13. what is the best tutorials for ccna courses ?
14. I want to know what kind of routers and switches are needed to setup Latest CCNA lab?
15. Help in understanding CCNA 3?
16. Age requirement for CCNA?
17. i m doing bca. need some information about the certification programs
18. difference between RIP1 and RIP2 in CCNA (networking)?
19. may i know the best institue for learning Hard ware networking, MCSA CCNA…
20. i am fade up of ccna!!!!!!!?
21. i am a computer science engg student of 2′nd year.Is CCNA is benifitial to me….
22. Cisco CCNA questions?
23. What is the latest dump (pass4sure) for ccna 640-802?
24. what is the scope of ccna?
25. CCNA Exploration 4, CCNA1: Network Fundamentals?
26. What should I do (MCSE/CCNA/RHCT) or (.NET/PHP) to get a better job in India
27. New IT Community
28. How to get latest ccna & mcse dumps for online?
29. what is new ccna dumps version?
30. Is there any computer centre in bangalore which offers CCNA a week course?
31. In CCNA standard access list it works on source ip address but it is also block the
32. jave & p4s ccna latest one plz help ?
33. I Want To Go Through Ccna Exams But I Want A Self Study.so How I Can Apply For
34. need to join ccna coaching institute in delhi.any personnel experience is…
35. How can i view ccna nuggets on mobile ?
36. hello friends,i need to know about ccna,ccsp & other cisco certified exams. ?
37. What’s the best CCNA study guide out there?
38. Is CCNA a good certification?
39. What would you like to ask?which is the latest edition of ccna book by
40. which course should i opt for mcsa or ccna or mcne?
41. please, i want to know center for CCNA training in egypt?
42. I Find a Latest Exam Download
43. I need the RouterSim Ver2 authorisation key for my ccna ccna exam & dont have
44. What is CCNA course?What is the proceedure for appearing for the exam?
45. where do I get proper online MCSE and CCNA certification?
46. How to concentrate on my CCNA studies?
47. what is the career opportunity to be a graduate {b com pass} along with MCSE & CCNA ?
48. ccna 4 exploration semester 4 answers?
49. Who is the best CCNA teacher?
50. Syllabus for Cisco CCNA?
51. Where can I find CCNA 2 version 4.1 exam answers?
52. RHCE or MCSE or CCNA which is more better?
53. CCNA course material download?
54. If you have a CCNA….?
55. Answers of CCNA Exploration 4.0 Lab Manual?
56. Getting started in IT: Which certification to get first, CCNA or Network+?
57. CCNA exam – configuration questions?
58. help ccna questions, for computers?
59. I am RHCE certified, CCNA, MCSE trained have 6 months Linux teaching exp. How…
60. Is a CCNA Certification worth it?
61. CCNA Certification Help?
62. i want to do CCNA course but i dont have time i want to get traning online/is
63. Can you really pass the CCNA 640-802 test? with the Pass4Sure version 3.20?
64. Will study material for the CCNA 640-801 help me on the CCNA 640-802 ?
65. CCNA : route summarization?
66. hi. iam planning for CCNA certification exam ,and i hav heard that one can
67. CCNA practice help!!!!!!!!!!!?
68. Which of the following is more creative- J2EE, J2ME, .Net, CCNA,
69. What is the best way to study for the CCNA exam?
70. CCNA Answers and questions?
71. i am prasad i am CCNA, SCSA AND MCSA CERTIFIED person how much salary i
72. CCNA Exam and GUI tool ?
73. What is the basic qualification for CCNA exam?
74. Will Cisco CCNA certificate holders have good paying jobs?
75. ccna version 4.0 ch 3 answers?
76. What are the prereqs for CCNA? Networking in general?
77. CCNA question : i don’t understand the difference between the following :?
78. CCNA, is this valuable?
79. I have many questions to ask it instantly about ccna 1?
80. hi. iam planning for CCNA certification exam ,and i hav heard that one can get…
81. CCNA, is this valuable?
82. P4s Latest Working Dumbs Of Ccna(640-802) ? ?
83. What are the prereqs for CCNA? Networking in general?
84. CCNA : route summarization?
85. Can you really pass the CCNA 640-802 test? with the Pass4Sure version 3.20?
86. i want to do CCNA course but i dont have time i want to get traning
87. CCNA practice help!!!!!!!!!!!?
88. Can you really pass the CCNA 640-802 test? with the Pass4Sure version 3.20?
89. CCNA question : i don’t understand the difference between the following :?
90. CCNA Exam and GUI tool ?
91. Which of the following is more creative- J2EE, J2ME, .Net, CCNA,
92. i am prasad i am CCNA, SCSA AND MCSA CERTIFIED person how much salary i will
93. I have many questions to ask it instantly about ccna 1?
94. Can you really pass the CCNA 640-802 test? with the Pass4Sure version 3.20?
95. ccna certification and networkingjob?
96. CCNA Answers and questions?
97. What is the basic qualification for CCNA exam?
98. Will Cisco CCNA certificate holders have good paying jobs?
99. ccna or certificate in networking?
100. Does CCNA 1 counts as one A level?
101. Is a CCNA Certification worth it?
102. Syllabus for Cisco CCNA?
103. help ccna questions, for computers?
104. Can you really pass the CCNA 640-802 test? with the Pass4Sure version 3.20?
105. i want boson netsim for ccna 7.0 simulator with crack n serial?
106. Can you really pass the CCNA 640-802 test? with the Pass4Sure version 3.20?
107. help me regarding MCSE, CCNA, CCNP.?
108. CCNA course material download?
109. CCNA exam – configuration questions?
110. For Cisco CCNA 1 Discovery 4.0, Chapter 10 ?
111. I am going to take 2 Cisco classes, is CCNA test Hard?
112. Where can I find CCNA 2 version 4.1 exam answers?
113. CCNA, Comptia Certs, what will they get me salary wise?
114. CCNA Certification Help?
115. HELP ME PLEASE: Network + Certified or CCNA Certified?
116. Getting started in IT: Which certification to get first, CCNA or Network+?
117. Help me to study the CCNA?
118. How will I do online Course of ccna or MCSC plz suggest me which institute is best
119. CCNA Certification Help?
120. Answers of CCNA Exploration 4.0 Lab Manual?
121. ccna 4 exploration semester 4 answers?
122. Syllabus for Cisco CCNA?
123. how much is a CCNA worth ?
124. Syllabus for Cisco CCNA?
125. What are the best cisco router/switch emulators for assistance with CCNA course?
126. Who is the best CCNA teacher?
127. Getting Trained at Mumbai’s best training center for MCSE 2003, RHCE, CCNA…
128. where do I get proper online MCSE and CCNA certification?
129. How to concentrate on my CCNA studies?
130. plz snd me ccna exploration 1 v4.0 assessments+final answer ?
131. CCNA Practice Question?
132. can some one give me cisco ccna 640-802 Pass for sure study guide?
133. please send me ccna dump pass4sure version 3.20 to seawind2010@gmail.com ….
134. CCNA exam questions-change all the time?
135. what is ICND1 and ICND2 and what is the diffrent between it and CCNA??
136. Is It Worth to do CCNA online Exam for $250 ? please suggest me ?
137. What is career oportunities of mcse,ccna in india after Diploma in…
138. CCNA exam questions types!!!?
139. what is the latest version of ccna dumps ..2.95 or 3.10 ..ect?
140. am a b tech graduate and planning to take CCNA .. want to wrk abroad ?


141. Cisco CCNA or Professional Cookery NVQ Level 2?
142. The use of calculators for the CCNA exam ?
143. Hey guys i m studying for CCNA cert, can u please help me with websites
144. I am looking to do the CCNA but have very limited experience with regard to IT.
145. can u plez forward me latest pass4sure for ccna 640-802 dumps V18?
146. Valid CCNA book-exam topics?
147. which is the best ccna and mcse?
148. Who makes more to start: ccna or sql/oracle associate?
149. Can I get CCSP certified if i have a regular CCNA and not a CCNA in security?
150. What are the prospects of doing CCNA,CWNA,MCSA,RHCE collectively? Should I do
151. any one please help me with answers to CCNA exploration 4.0 assessment
152. CCNP certificate path after CCNA?
153. How and where can i get free CCNA 640-802 past questions and answers?
154. CCNA first, Or Easier Certification?
155. Who have ccna Q&A? i want to buy any !!!!?
156. Which CCNA is in demand(design, security,switches, storage, networking)!!!
157. CISCO CCNA books !!!
158. What is the current cost of CCNA- 640-802 exams? Is the any hike in fees…
159. ccna 1 IT Essentials: PC Hardware and Software v4.0 exam answers
160. SAP and CCNA in United Arab Emirates?
161. what is the exam amount of ccna?
162. what is the latest code of CCNA Exam
163. I’ve completed my MCSE, Continuing with CCNA & LINUX. Where I’ll Get real…
164. Cisco CCNA is this worth it
165. Plz help me …CCNA simulator.Urgent needed !
166. do you want to study ccna for free ?
167. Please help, question about CCNA. . .?
168. any one knows updates about ccna 640-802???
169. ccna exam fee?
170. Which is the better network simulator, Boson Netsim or CCNA network visualizer?
171. I have CCNA from Brain Dumps, no hands-on experience. I am going to
172. i can install CCNA V4 exploartion on my vista home laptop any one who knows how?
173. What is the CCNA exam like?
174. what is the lastest version of pass4sure for ccna exam 640-802?
175. Is Bosom Netsim 7.0 a good program to prepare for the 640-802 CCNA?
176. Where to download a CCNA 2 exploration student lab manual?
177. where will teach ccna course in chennai?
178. Planning for CCNA exam (640-802). Which 2 study materials would you recommend?
179. i have downloaded a ccna material whichis of .bin and .cue file from rapidshare?
180. How well does having a CCNA translate to radio communications of the future?
181. am 10th pass guy in 1998 from delhi. I want to do CCNA online to get better job ….
182. What the cheapest but most effective way to get my CCNA from Cisco?
183. which is the best institute in surat for ccna teaching?
184. I would like to take the new CCNA exam , will anyone tell me how it is
185. How much does CCNA exam cost?
186. where is the best CCNA training center for beginners with a very good instructor…
187. hi fnds i m preparing for CCNA exam. pls can u tell me which book is better
188. how can I make sure if someone have really CCNA?
189. CCNA Exam Preparation?
190. which is best institute for CCNA & MCSC course?
191. can you help me to my the CCNA study?
192. I am 10th pass guy in 1998 from delhi. I want to do CCNA online to get better job .
193. Are there any jobs for a Cisco CCNA in the Tampa area?
194. should i do only ccna or sholud i do ccna with mcse or rhce?
195. RouterSim’s CCNA™ Network Visualizer® 5.0?
196. hv one of u got this ebook? CCNA Exploration Networking Fundamentals?
197. about ccna?
198. Is CCNA courses good way ?
199. Please tell me where i can give the CCNA exam and which is the best institute for…
200. CCNA 4 accessing the WAN chapter 1?
201. Hi guys Im CCNA & MCP certified Looking for Network Engineer job?
202. CCNA 4 exploration 4 Accessing the WAN chapter 1 exam question?
203. CCNA 4 exploration 4 Accessing the WAN chapter 1 exam question?
204. CCNA Score?
205. can anybudy guide me abt CCNA CCIE is the best or SAP HR is the best for
206. What will be better for me career wise, a CCNA cert or the military?
207. IT Questions.. CCNA.. A+.. Network+..?
208. what would be career path for CCNA and CCNP course?
209. Is it possible to get CCNA in 30 Days with basic Networking skills? If so
210. I have done a course in msce and ccna networking certification through microsoft?
211. Pls where can i get cisco router simulator for studying my CCNA??
212. need ccna & remote access telnet commands?
213. hi, preparing for CCNA exam, some body told that exam fees s increased is it true???
214. What definition of CCNA?
215. where can u get answers for exploration1and2mode8 exams for ccna?
216. hi i am preparing for CCNA exam, some body told that exam fees s is it true!!???
217. CCNA Discovery 4.0 answers?
218. How much % of marks should i get to get pass in CCNA?
219. i m doing software eng(diplm) frm nt so reputed inst alng wid ccna frm cisco….
220. Where i can get ccna 1 version 4.0 module exam and final exam question?
221. I want the intitutes phone no and address, i m planning 2 take up course on
222. CCNA security coaching??
223. ccna security coaching??
224. Can you answer this CCNA question?
225. pls give little hint abt course ware for CCNA?
226. is it difficult to learn and pass CCNA exam?
227. Anyone else studying for their CCNA ?
228. CCNA & JAVA! Which one Steady degree of work ?
229. what is the best book to be refered to ccna?
230. How many CCNA certificates required to reach expert level and….?
231. How many CCNA certificates required to reach expert level and….?
232. CCNA 1 Discovery Networking for home and small office v 4.0, Chapter 8…
233. CCNA exam fee?
234. CCNA jobs in miami FL?
235. CCNA 801 vs 802?
236. ccna course?
237. Will a CCNA certification after which companies can work ?
238. Made ccna license?
239. What will the future development of CCNA?
240. partime job in delhi after ccna?
241. Collision domains – CCNA question?
242. ccna frm indore??
243. GOOD INSTITUTE FOR CCNA IN DELHI or INDIA?
244. i need to practice for ccna which?
245. What is the differense of the CCNA (640-801) and Cisco Certified Network…
246. what does a ccna do?
247. CCNA and NNCS network certification questions?
248. CCNA 2 topology help, really stuck?
249. What are the job prospects after completing the CCNA course ? I am confused ,…
250. which is the good institute in Delhi for doing CCNA and hardware/networking course?

Thursday, December 11, 2008

CCNA EXAM INFO


Greetings,

Here are some helpful info about CCNA . the 640-801 exam covers:

Understanding the functions and operations of local area networks (LAN)
Cisco IOS fundamentals
Wide area networks (WAN)
Virtual private networks (VPN)
Storage Area Networks (SAN)
IP Addressing
Cisco Command Line Interface (CLI)
Routing and Switching technologies and protocols


This exam is the recommended approach for those candidates who have some computing and networking experience, or who don't want to bother with the time and cost associated with taking two exams rather than one.

The Layered, Two Exam, Approach

Alternatively, a candidate, likely one quite new to networking or one who likes to break one goal into two smaller milestones, may take two exams to achieve the CCNA.

The first of these CCNA exams is the entry-level one, the Cisco Networking Technologies (INTRO), exam number 640-821. This exam is presently in beta as exam number 641-821.

This exam is a great launching pad for those new to networking and who already have or are considering taking CompTIA's Network+ certification. Taking both the Network+ and the INTRO exam would round out your knowledge of introductory networking concepts. Moreover, you'd get both a vendor-specific and vendor-neutral look at networking. In fact, getting dual-certified on these entry level networking certifications can be leveraged to more prestigious titles. The Network+ can be used as an elective to more advanced networking certifications, such as Novell's CNE and Microsoft's MCSA. In terms of Cisco's INTRO exam, passing it will help you break the CCNA task into two chunks and give you confidence to take the second exam required for your CCNA and to then perhaps move onto more advance Cisco certifications, such as the CCNP (Cisco Certified Network Professional).

The second, two-step CCNA exam is the Interconnecting Cisco Network Devices (ICND), exam number 640-811, which just released on June 30, 2003. This exam "covers topics on Extending Switched Networks with VLANS, Determining IP Routes, Managing IP traffic with Access Lists, Establishing Pont-toPoint connections, and Establishing Frame Relay Connections."


CCNA EXAM INFO


Greetings,

Here are some helpful info about CCNA . the 640-801 exam covers:

Understanding the functions and operations of local area networks (LAN)
Cisco IOS fundamentals
Wide area networks (WAN)
Virtual private networks (VPN)
Storage Area Networks (SAN)
IP Addressing
Cisco Command Line Interface (CLI)
Routing and Switching technologies and protocols


This exam is the recommended approach for those candidates who have some computing and networking experience, or who don't want to bother with the time and cost associated with taking two exams rather than one.

The Layered, Two Exam, Approach

Alternatively, a candidate, likely one quite new to networking or one who likes to break one goal into two smaller milestones, may take two exams to achieve the CCNA.

The first of these CCNA exams is the entry-level one, the Cisco Networking Technologies (INTRO), exam number 640-821. This exam is presently in beta as exam number 641-821.

This exam is a great launching pad for those new to networking and who already have or are considering taking CompTIA's Network+ certification. Taking both the Network+ and the INTRO exam would round out your knowledge of introductory networking concepts. Moreover, you'd get both a vendor-specific and vendor-neutral look at networking. In fact, getting dual-certified on these entry level networking certifications can be leveraged to more prestigious titles. The Network+ can be used as an elective to more advanced networking certifications, such as Novell's CNE and Microsoft's MCSA. In terms of Cisco's INTRO exam, passing it will help you break the CCNA task into two chunks and give you confidence to take the second exam required for your CCNA and to then perhaps move onto more advance Cisco certifications, such as the CCNP (Cisco Certified Network Professional).

The second, two-step CCNA exam is the Interconnecting Cisco Network Devices (ICND), exam number 640-811, which just released on June 30, 2003. This exam "covers topics on Extending Switched Networks with VLANS, Determining IP Routes, Managing IP traffic with Access Lists, Establishing Pont-toPoint connections, and Establishing Frame Relay Connections."